Failure mode, effects, and criticality analysis


Failure mode effects and criticality analysis is an extension of failure mode and effects analysis.
FMEA is a bottom-up, inductive analytical method which may be performed at either the functional or piece-part level. FMECA extends FMEA by including a criticality analysis, which is used to chart the probability of failure modes against the severity of their consequences. The result highlights failure modes with relatively high probability and severity of consequences, allowing remedial effort to be directed where it will produce the greatest value. FMECA tends to be preferred over FMEA in space and North Atlantic Treaty Organization military applications, while various forms of FMEA predominate in other industries.

History

FMECA was originally developed in the 1940s by the U.S military, which published MIL-P-1629 in 1949. By the early 1960s, contractors for the U.S. National Aeronautics and Space Administration were using variations of FMECA under a variety of names. In 1966 NASA released its FMECA procedure for use on the Apollo program. FMECA was subsequently used on other NASA programs including Viking, Voyager, Magellan, and Galileo.
Possibly because MIL-P-1629 was replaced by MIL-STD-1629 in 1974, development of FMECA is sometimes incorrectly attributed to NASA.
At the same time as the space program developments, use of FMEA and FMECA was already
spreading to civil aviation. In 1967 the Society for Automotive
Engineers released the first civil publication to address FMECA. The civil aviation industry now tends to use a combination of FMEA and Fault Tree Analysis in accordance with SAE ARP4761 instead of FMECA, though some helicopter manufacturers continue to use FMECA for civil rotorcraft.
Ford Motor Company began using FMEA in the 1970s after problems experienced with its Pinto
model, and by the 1980s FMEA was gaining broad use in the automotive industry. In Europe,
the International Electrotechnical Commission published IEC 812 in 1985, addressing both FMEA and FMECA for general use. The British Standards Institute published BS 5760-5 in 1991 for the same purpose.
In 1980, MIL-STD-1629A replaced both MIL-STD-1629 and the 1977 aeronautical FMECA standard MIL-STD-2070. MIL-STD-1629A was canceled without replacement in 1998, but nonetheless remains in wide use for military and space applications today.

Methodology

Slight differences are found between the various FMECA standards. By RAC CRTA-FMECA, the FMECA analysis procedure typically consists of the following logical steps:
FMECA may be performed at the functional or piece-part level. Functional FMECA considers the effects of failure at the functional block level, such as a power supply or an amplifier.
Piece-part FMECA considers the effects of individual component failures, such as resistors,
transistors, microcircuits, or valves. A piece-part FMECA requires far more effort, but provides the benefit of better estimates of probabilities of occurrence. However, Functional FMEAs can be performed much earlier, may help to better structure the complete risk assessment and provide other type of insight in mitigation options. The analyses are complementary.
The criticality analysis may be quantitative or qualitative, depending on the availability of supporting part failure data.

System definition

In this step, the major system to be analyzed is defined and partitioned into an indented
hierarchy such as systems, subsystems or equipment, units or subassemblies, and piece-parts. Functional descriptions are created for the systems and allocated to the subsystems,
covering all operational modes and mission phases.

Ground rules and assumptions

Before detailed analysis takes place, ground rules and assumptions are usually defined and agreed to. This might include, for example:
Next, the systems and subsystems are depicted in functional block diagrams. Reliability
block diagrams or fault trees are usually constructed at the same time. These diagrams are
used to trace information flow at different levels of system hierarchy, identify critical
paths and interfaces, and identify the higher level effects of lower level failures.

Failure mode identification

For each piece-part or each function covered by the analysis, a complete list of failure
modes is developed. For functional FMECA, typical failure modes include:
For piece-part FMECA, failure mode data may be obtained from databases such as RAC
FMD-91 or RAC FMD-97. These databases provide not only the failure modes, but also the failure mode
ratios. For example:
Device TypeFailure ModeRatio
RelayFails to trip.55
Spurious trip.26
Short.19
Resistor, CompositionParameter change.66
Open.31
Short.03

Each function or piece-part is then listed in matrix form with one row for each failure
mode. Because FMECA usually involves very large data sets, a unique identifier must be assigned to each item, and to each failure mode of each item.

Failure effects analysis

Failure effects are determined and entered for each row of the FMECA matrix, considering the
criteria identified in the ground rules. Effects are separately described for the local, next higher, and end levels. System level effects may include:
The failure effect categories used at various hierarchical levels are tailored by the
analyst using engineering judgment.

Severity classification

Severity classification is assigned for each failure mode of each unique item and entered on the FMECA matrix, based upon system level consequences. A small set of classifications,
usually having 3 to 10 severity levels, is used. For example, When prepared using MIL-STD-1629A, failure or mishap severity classification normally follows MIL-STD-882.
CategoryDescriptionCriteria
ICatastrophicCould result in death, permanent total disability, loss exceeding $1M, or irreversible severe environmental damage that violates law or regulation.
IICriticalCould result in permanent partial disability, injuries or occupational illness that may result in hospitalization of at least three personnel, loss exceeding $200K but less than $1M, or reversible environmental damage causing a violation of law or regulation.
IIIMarginalCould result in injury or occupational illness resulting in one or more lost work day, loss exceeding $10K but less than $200K, or mitigatible environmental damage without violation of law or regulation where restoration activities can be accomplished.
IVNegligibleCould result in injury or illness not resulting in a lost work day, loss exceeding $2K but less than $10K, or minimal environmental damage not violating law or regulation.

Current FMECA severity categories for U.S. Federal Aviation Administration, NASA and European Space Agency space applications are derived from MIL-STD-882.

Failure detection methods

For each component and failure mode, the ability of the system to detect and report the
failure in question is analyzed. One of the following will be entered on each row of the FMECA matrix:
Failure mode criticality assessment may be qualitative or quantitative. For qualitative
assessment, a mishap probability code or number is assigned and entered on the matrix. For
example, MIL-STD-882 uses five probability levels:
DescriptionLevelIndividual ItemFleet
FrequentALikely to occur often in the life of the itemContinuously experienced
ProbableBWill occur several times in the life of an itemWill occur frequently
OccasionalCLikely to occur some time in the life of an itemWill occur several times
RemoteDUnlikely but possible to occur in the life of an itemUnlikely, but can reasonably be expected to occur
ImprobableESo unlikely, it can be assumed occurrence may not be experiencedUnlikely to occur, but possible

The failure mode may then be charted on a criticality matrix using severity code as one axis
and probability level code as the other.
For quantitative assessment, modal criticality number is calculated for each failure mode of each item, and item criticality number is
calculated for each item. The criticality numbers are computed using the following values:
The criticality numbers are computed as and.
The basic failure rate is usually fed into the FMECA from a failure rate prediction based on MIL-HDBK-217, PRISM, RIAC 217Plus, or a similar
model.
The failure mode ratio may be taken from a database source such as RAC FMD-97. For functional level FMECA, engineering judgment may be required to assign failure mode ratio.
The conditional probability number represents the conditional
probability that the failure effect will result in the identified severity classification,
given that the failure mode occurs. It represents the analyst's best judgment as to the
likelihood that the loss will occur.
For graphical analysis, a criticality matrix may be charted using either or on one axis and severity code on the other.

Critical item/failure mode list

Once the criticality assessment is completed for each failure mode of each item, the FMECA matrix may be sorted by severity and qualitative probability level or quantitative
criticality number. This enables the analysis to identify critical items and critical
failure modes for which design mitigation is desired.

Recommendations

After performing FMECA, recommendations are made to design to reduce the consequences of critical failures. This may include selecting components with higher reliability, reducing
the stress level at which a critical item operates, or adding redundancy or monitoring to the system.

Maintainability analysis

FMECA usually feeds into both Maintainability Analysis and Logistics Support Analysis, which both require data from the FMECA. FMECA is the most popular tool for failure and criticality analysis of systems for performance enhancement. In the present era of Industry 4.0, the industries are implementing a predictive maintenance strategy for their mechanical systems. The FMECA is widely used for the failure mode identification and prioritization of mechanical systems and their subsystems for predictive maintenance.

FMECA report

A FMECA report consists of system description, ground rules and assumptions, conclusions and
recommendations, corrective actions to be tracked, and the attached FMECA matrix which may
be in spreadsheet, worksheet, or database form.

Risk priority calculation

RAC CRTA-FMECA and MIL-HDBK-338 both identify Risk Priority Number
calculation as an alternate method to criticality analysis. The RPN is a result
of a multiplication of detectability x severity x
occurrence. With each on a scale from 1 to 10, the highest RPN is
10x10x10 = 1000. This means that this
failure is not detectable by inspection, very severe and the occurrence is almost sure. If
the occurrence is very sparse, this would be 1 and the RPN would
decrease to 100. So, criticality analysis enables to focus on the highest risks.

Advantages and disadvantages

Strengths of FMECA include its comprehensiveness, the systematic establishment of relationships between failure causes and effects, and its ability to point out individual failure modes for corrective action in design. Weaknesses include the extensive labor required, the large number of trivial cases considered, and inability to deal with multiple-failure scenarios or unplanned cross-system effects such as sneak circuits.
According to an FAA research report for commercial space transportation,