EMD GT22 Series


The EMD GT22 Series were first introduced in 1972 after the rise in popularity of six axle locomotives. The GT series now carried a turbocharger that increased the horsepower depending on customer input. The GT series also utilized six axle HTC Trucks, which allowed the locomotive to haul heavier loads at slower speeds with minimal wheelslip.
The GT22C series also gave itself various individual designations depending on customer input. Standard suffixes after the model designation were either a U or W suffix to indicate the type of traction motors. A C generally indicated six axle trucks but due to a six axle locomotive being too oversized for most second and third world countries, EMD developed the L suffix to indicate the locomotive was constructed with a Lightweight frame. EMD Dash 2 electronics also became a popular choice for the export railroads by the late 1970s.
These designations could apply to any kind of export locomotive design of EMD or another licensee of EMD as long as the electrical & mechanical gear was left unaltered.

Overview

With the introduction of the 645 engine for export models in 1967, the model designation numbers changed by adding 10 to the designation of a similar model. To meet customer demands of a six axle version of the popular G12, EMD created the GR12 which was slightly longer and taller to accommodate the Type-C trucks.
EMD then designed the GT22 model to accommodate the HT-C truck first found on the American EMD SD45X. Extending the carbody and increasing the fuel tank capacity, the GT22C series was introduced. Production spanned longer than the four axle G22 version, but with smaller orders.
Several models were introduced:
The EMD GT22CW was first appeared in 1972 and now carried a CW suffix which indicated that this model had six axles and traction motors that could fit from to gauge tracks. Another new suffix introduced to this model was the T, which indicated the use of a turbocharger.
The GT22CW found most of its popularity in Argentina, while two unusual orders went to the Saudi Railways Organization in Saudi Arabia & the Société Nationale des Transports Ferroviaires of Algeria.
Production spanned from July 1972 to February 1988

GT22CU

The EMD GT22CU was first appeared in 1972. Designed mainly for the narrow gauge market, the GT22CU now carried a CU suffix which indicated that this model had six axles and traction motors that could fit from one meter to gauge tracks. Another new suffix introduced to this model was the T, which indicated the use of a turbocharger.
The GT22CU was purchased by the Ferrocarriles Argentinos from June 1972 to January 1980.

GT22CW-2

The EMD GT22CW-2 was first appeared in 1988 and now carried a CW suffix which indicated that this model had six axles and traction motors that could fit from Standard Gauge rails to gauge tracks. Another new suffix introduced to this model was the T, which indicated the use of a turbocharger. Finally, this model now carried the popular EMD Dash 2 electronics which improved its reliability.
The GT22CW-2 found most of its popularity in Argentina and even after the breakup of Ferrocarriles Argentinos, did the successors of that company continued to purchase more GT22CW-2s.
Production spanned from March 1988 to December 1997.

GT22HW-2

The GT22HW-2 was a departure from the standard production of the GT22 Series as it was a custom model designed to meet the conditions of Yugoslavia. This multipurpose locomotive was introduced with a turbocharger, Head End Power for passenger use and EMD Dash 2 Electronics, with an A1A-A1A axle arrangement. Due to the locomotive's compact appearance, the length was shortened by 1.25 feet from a normal GT22CW-2. Thirty four of these locomotives were manufactured by Đuro Đaković between February 1981 and August 1984. Since Yugoslavia had various languages arising from the ethnicities in the country, the locomotives were given four different lettering variations:

GT22CUM

First introduced in January 1982, the GT22CUM series were locomotives were a powerful single-engined locomotive with light weight per-axle. Designed exclusively for the RFFSA by Equipmentos Villares S.A., the GT22CUM now carried a CU suffix which indicated that this model had six axles and traction motors that could fit from one meter to gauge tracks. Two custom designations were introduced for this locomotive: M for meter gauge and -1/-2 to indicate a Type 1 or Type 2 model.
Production spanned from January 1982 to May 1986.
All subsidiaries of the RFFSA were consolidated in 1983 with the introduction of the SIGO System by the federal government.

GT22LC

When most second and third world railroads couldn't operate standard EMD GT22s due to their weight, EMD introduced the GT22LC; which is the same as a GT22C, but now incorporated with a much lighter frame to handle harsher conditions than normal while still equipped with a turbocharger. Due to the lightweight frame, the U or W suffixes no longer applied as the locomotive was designed to handle any rail gauge the locomotive is applied to.
Production spanned from February 1985 to August 1986.

GT22LC-2

Basically the same as the GT22LC, the GT22LC-2 now added EMD Dash 2 Electronics while still retaining a turbocharger. Due to the Lightweight frame, the U or W suffixes no longer applied.
Production spanned from November 1981 to November 1996.