A booster engine for steam locomotives is a small two-cylinder steam engine back-gear-connected to the trailing truck axle on the locomotive or the lead truck on the tender. A rockingidler gear permits it to be put into operation by the driver. It drives one axle only and can be non-reversible, with one idler gear, or reversible, with two idler gears. A booster engine is used to start a heavy train or maintain low speed under demanding conditions. Rated at about at speeds of from, it can be cut in while moving at speeds under and is semi-automatically cut out via the engineer notching back the reverse gear between, depending on the model and design of the booster. A tractive effort of is common, although ratings of up to around were possible. Tender boosters are equipped with side-rods connecting axles on the lead truck. Such small side-rods restrict speed and are therefore confined to switching locomotives, often used in transfer services between yards. Tender boosters were far more rare than engine boosters.
Reasons for booster use
The booster is intended to make up for fundamental flaws in the design of the standard steam locomotive. First, most steam locomotives do not provide power to all wheels. The amount of force that can be applied to the rail depends on the weight on the driven wheels and the factor of adhesion of the wheels against the track. Unpowered wheels are generally needed to provide stability at speed, but at low speed they are not required, so they effectively 'waste' weight which could be used for traction. Second, the "gearing" of a steam locomotive is constant, because the pistons are linked directly to the wheels via rods and cranks. Therefore, a compromise must be struck between ability to haul at low speed and the ability to run fast without inducing excessive piston speeds, or the exhaustion of steam. That compromise means that, at low speeds, a steam locomotive is not able to use all the power the boiler is capable of producing; it simply cannot use steam that quickly, so there is a big difference between the amount of steam the boiler can produce and the amount that can be used. The booster engine enables that wasted potential to be put to use.
Disadvantages
Boosters are costly to maintain, with their flexible steam and exhaust pipes, idler gear, etc. Improper operation could also result in undesirable drops in boiler pressure and/or damage to the booster.
The booster saw most use in North America. Railway systems elsewhere often considered the expense and complexity unjustified. Even in the North American region, booster engines were applied to only a fraction of all locomotives built. Some railroads used boosters extensively while others did not. The New York Central was a fan of booster engines and applied them to all of its 4-6-4Hudson locomotives. The rival Pennsylvania Railroad, however, used few booster-equipped locomotives. Canadian Pacific Railway rostered 3,257 steam locomotives acquired between 1881 and 1949, yet only 55 were equipped with boosters. 17 H1 class 4-6-4s, 2 K1 class 4-8-4s and all 36 T1 class 2-10-4s.
Australia
In Australia, Victorian Railways equipped all but one of its X class2-8-2 locomotives with a 'Franklin' two-cylinder booster engine, following a successful trial of the device on a smaller N class 2-8-2 in 1927. From 1929 onwards, South Australian Railways 500 class 4-8-2 heavy passenger locomotives were rebuilt into 4-8-4s with the addition of a booster truck.
New Zealand
's Kb class of 1939 were built with a booster truck to enable the locomotives to handle the steeper grades of some South Island lines. Some boosters were later removed because of the gear jamming.
In Great Britain, eight locomotives of four different classes on the London and North Eastern Railway were equipped with booster units by Nigel Gresley. Four were existing locomotives rebuilt with boosters between 1923 and 1932: one of class C1 ; both of the conversions from class C7 to class C9 ; and one of class S1. The remaining four were all fitted to new locomotives: the two P1 2-8-2 locomotives, built in 1925; and two class S1 locomotives built in 1932. The boosters were removed between 1935 and 1938, apart from those on class S1 which were retained until 1943. An early type of booster used in Great Britain was the steam tender, which was tried in 1859 by Benjamin Connor of the Caledonian Railway on four 2-4-0 locomotives. Archibald Sturrock of the Great Northern Railway patented a similar system on 6 May 1863. It was used on fifty GNR 0-6-0 locomotives: thirty converted from existing locomotives between 1863 and 1866, and twenty built new in 1865. The equipment was removed from all fifty during 1867–68.
