Z-test


A Z-test is any statistical test for which the distribution of the test statistic under the null hypothesis can be approximated by a normal distribution. Z-test tests the mean of a distribution. For each significance level in the confidence interval, the Z-test has a single critical value which makes it more convenient than the Student's t-test whose critical values are defined by the sample size.
Because of the central limit theorem, many test statistics are approximately normally distributed for large samples. Therefore, many statistical tests can be conveniently performed as approximate
Z-tests if the sample size is large or the population variance is known. If the population variance is unknown and the sample size is not large, the Student's t-test may be more appropriate.
How to perform a Z test when
T is a statistic that is approximately normally distributed under the null hypothesis is as follows:
First, estimate the expected value μ of
T under the null hypothesis, and obtain an estimate s of the standard deviation of T.
Second, determine the properties of
T : one tailed or two tailed.
For Null hypothesis
H0: μ≥μ0 vs alternative hypothesis H1: μ<μ0, it is upper/right-tailed.
For Null hypothesis
H0: μ≤μ0 vs alternative hypothesis H1: μ>μ0, it is lower/left-tailed.
For Null hypothesis
H0: μ=μ0 vs alternative hypothesis H1: μ≠μ0, it is two-tailed.
Third, calculate the standard score :
,
which one-tailed and two-tailed p-values can be calculated as Φ, Φ and 2Φ where Φ is the standard normal cumulative distribution function.

Use in location testing

  1. The term "Z-test" is often used to refer specifically to the one-sample location test comparing the mean of a set of measurements to a given constant when the sample variance is known. For example, if the observed data X1,..., Xn are independent, have a common mean μ, and have a common variance σ2, then the sample average X has mean μ and variance.
  2. The null hypothesis is that the mean value of X is a given number μ0. We can use X as a test-statistic, rejecting the null hypothesis if X − μ0 is large.
  3. To calculate the standardized statistic, we need to either know or have an approximate value for σ2, from which we can calculate . In some applications, σ2 is known, but this is uncommon.
  4. If the sample size is moderate or large, we can substitute the sample variance for σ2, giving a plug-in test. The resulting test will not be an exact Z-test since the uncertainty in the sample variance is not accounted for—however, it will be a good approximation unless the sample size is small.
  5. A t-test can be used to account for the uncertainty in the sample variance when the data are exactly normal.
  6. Difference between Z-test and t-test: Z-test is used when sample size is large, or the population variance is known. t-test is used when sample size is small and population variance is unknown.
  7. There is no universal constant at which the sample size is generally considered large enough to justify use of the plug-in test. Typical rules of thumb: the sample size should be 50 observations or more.
  8. For large sample sizes, the t-test procedure gives almost identical p-values as the Z-test procedure.
  9. Other location tests that can be performed as Z-tests are the two-sample location test and the paired difference test.

    Conditions

For the Z-test to be applicable, certain conditions must be met.
If estimates of nuisance parameters are plugged in as discussed above, it is important to use estimates appropriate for the way the data were sampled. In the special case of Z-tests for the one or two sample location problem, the usual sample standard deviation is only appropriate if the data were collected as an independent sample.
In some situations, it is possible to devise a test that properly accounts for the variation in plug-in estimates of nuisance parameters. In the case of one and two sample location problems, a t-test does this.

Example

Suppose that in a particular geographic region, the mean and standard deviation of scores on a reading test are 100 points, and 12 points, respectively. Our interest is in the scores of 55 students in a particular school who received a mean score of 96. We can ask whether this mean score is significantly lower than the regional mean—that is, are the students in this school comparable to a simple random sample of 55 students from the region as a whole, or are their scores surprisingly low?
First calculate the standard error of the mean:
where is the population standard deviation.
Next calculate the z-score, which is the distance from the sample mean to the population mean in units of the standard error:
In this example, we treat the population mean and variance as known, which would be appropriate if all students in the region were tested. When population parameters are unknown, a t test should be conducted instead.
The classroom mean score is 96, which is −2.47 standard error units from the population mean of 100. Looking up the z-score in a table of the standard normal distribution cumulative probability, we find that the probability of observing a standard normal value below −2.47 is approximately 0.5 − 0.4932 = 0.0068. This is the one-sided p-value for the null hypothesis that the 55 students are comparable to a simple random sample from the population of all test-takers. The two-sided p-value is approximately 0.014.
Another way of stating things is that with probability 1 − 0.014 = 0.986, a simple random sample of 55 students would have a mean test score within 4 units of the population mean. We could also say that with 98.6% confidence we reject the null hypothesis that the 55 test takers are comparable to a simple random sample from the population of test-takers.
The Z-test tells us that the 55 students of interest have an unusually low mean test score compared to most simple random samples of similar size from the population of test-takers. A deficiency of this analysis is that it does not consider whether the effect size of 4 points is meaningful. If instead of a classroom, we considered a subregion containing 900 students whose mean score was 99, nearly the same z-score and p-value would be observed. This shows that if the sample size is large enough, very small differences from the null value can be highly statistically significant. See statistical hypothesis testing for further discussion of this issue.

''Z''-tests other than location tests

Location tests are the most familiar Z-tests. Another class of Z-tests arises in maximum likelihood estimation of the parameters in a parametric statistical model. Maximum likelihood estimates are approximately normal under certain conditions, and their asymptotic variance can be calculated in terms of the Fisher information. The maximum likelihood estimate divided by its standard error can be used as a test statistic for the null hypothesis that the population value of the parameter equals zero. More generally, if is the maximum likelihood estimate of a parameter θ, and θ0 is the value of θ under the null hypothesis,
can be used as a Z-test statistic.
When using a Z-test for maximum likelihood estimates, it is important to be aware that the normal approximation may be poor if the sample size is not sufficiently large. Although there is no simple, universal rule stating how large the sample size must be to use a Z-test, simulation can give a good idea as to whether a Z-test is appropriate in a given situation.
Z-tests are employed whenever it can be argued that a test statistic follows a normal distribution under the null hypothesis of interest. Many non-parametric test statistics, such as U statistics, are approximately normal for large enough sample sizes, and hence are often performed as Z-tests.