Turbomeca Astafan


The Turbomeca Astafan is a single-spool, variable-pitch turbofan engine developed from the Turbomeca Astazou. Despite successful flight-testing, an efficient, quiet and clean design and some commercial interest, the Astafan never entered series production. The engines were only flown on the Fouga 90 prototype and Turbomeca's two test aircraft.

Design

The engine combines an Astazou-derived centrifugal compressor with up to three axial compressor stages, driven by a common driveshaft. The fan section is composed of a unique variable pitch fan and fixed stator blades mounted at the front of the engine. Blade pitch is varied by a hydraulic piston mounted in the fan hub, while the fan itself is powered via a reduction gear from the main driveshaft.
The engine is designed to operate at a constant speed, no matter the thrust output—a characteristic permitted by the Astafan's use of precise fuel metering and fan blade pitch adjustment. To control the engine, the pilot first sets the speed lever, which adjusts fuel flow in proportion to the selected engine speed. Then the pilot moves the thrust lever, actuating the fan pitch piston by way of a mechanical linkage and hydraulic valve, and varying the blade pitch. In response, the speed governor holds engine speed steady by adjusting fuel delivery to the combustor. The control system also monitors turbine temperature and adjusts blade pitch to maintain it within the preferred range of to. Additionally, the system automatically protects against excessive fuel delivery or unusual changes in blade pitch. Using the thrust lever, pilots can start an Astafan in fine pitch, select takeoff pitch, feather the fan, or even reverse the fan pitch in flight.

Development

Flying testbeds

Turbomeca owned two Rockwell Turbo Commander aircraft, and arranged for Miles Aircraft to modify each of them to accept two podded Astafan engines inboard of the nacelles. The nacelles were stripped of their turboshaft engines, and converted to carry extra fuel. One of the Turbo Commanders, a model 680V-TU, originally bore the experimental registry F-WSTM, and was later redesignated F-BSTM. The other Turbo Commander, F-BXAS, was either a 690A or B model.

Variants

Astafan I

First run as a prototype in 1969, and first flown in 1971, the Astafan I was derived from the core of the Astazou XIV turboshaft. It was capable of outputting of dry thrust at takeoff power, or of thrust with water-methanol injection.

Astafan II

The Astafan II line was based on the Astazou XVI turboshaft engine core with a cooled turbine, and was governed to operate at.

Astafan II

The basic Astafan II received its French certification in August 1972. Early Astafan IIs were rated for approximately dry thrust at takeoff power, or with water-methanol injection.

Astafan IIA

The Astafan IIA was certified in 1972. It differed from the earlier Astafan II by incorporating a new, larger-diameter fan with blades that had a greater range of motion. Thrust output of the IIA was .

Astafan IIB4

Two IIB4s were installed on F-BSTM and used for testing and demonstration flights. This version was rated at of thrust.

Astafan IIG

The IIG was installed on the prototype of Aérospatiale's Fouga 90 jet trainer. Using this medium-bypass version of the Astafan instead of the Turbomeca Marboré, the 90 had twice the range of the Magister. Installed in the Fouga 90, and operating at its maximum thrust of, the IIG's specific fuel consumption was . At altitude and Mach 0.5, specific fuel consumption was .
The IIG included the Astafan's characteristic variable-pitch fan, installed in front of an Astazou XVI core. The design also included an annular reverse-flow combustor and a three-stage turbine section. The resulting configuration yielded a bypass ratio of 8.8 and a pressure ratio of 9.1.

Astafan III

The Astafan III used the Astazou XVI core and a cooled turbine. The dry thrust rating at takeoff was, and with water-methanol injection, thrust rose to .

Astafan IV

The Astafan IV was based upon the Astazou XX turboshaft's core, and used three axial compressor stages before the Astazou-derived centrifugal compressor. Like the Astafan II, the IV was governed at. The Astafan IV was considered for installation in the Fouga 90, as a more powerful alternative to the IIG.

Astafan IVF6

The IVF6 was tested on F-BXAS, and the engines were retained during that aircraft's time as a company transport. This version of the engine output of thrust at takeoff power.

Applications

Constructed

The Astafan was flown as a developmental engine on two aircraft types:
Despite its many developmental variants, the Astafan was never produced in commercial quantities. Proposed installations included: