Turbo-Hydramatic


Turbo-Hydramatic or Turbo Hydra-Matic is the registered tradename for a family of automatic transmissions developed and produced by General Motors. These transmissions mate a three-element turbine torque converter to a Simpson planetary geartrain, providing three forward speeds plus reverse.
The Turbo-Hydramatic or Turbo Hydra-Matic series was developed to replace both the original Hydra-Matic models and the Buick Dynaflow. In its original incarnation as the Turbo-Hydramatic 400, it was first used in the 1964 model year in Cadillacs. The Buick version, which followed shortly thereafter, was known as the Super-Turbine 400. By 1973, THM units had replaced all of GM's other automatic transmissions including Chevrolet's Powerglide, Buick's Super Turbine 300, and Oldsmobile's Jetaway. Starting in the early 1980s, the Turbo-Hydramatic was gradually supplanted by four-speed automatics, some of which continue to use the "Hydramatic" trade name.
Although the Turbo Hydra-Matic name alludes to the original Hydra-Matic developed by General Motors' Cadillac division in the late 1930s, the two transmissions were not mechanically related.

Super Turbine 400 / THM400 / THM375 / 3L80 / 3L80HD

The THM400 can be visually identified by an oil pan number four shown at . First introduced for the 1964 model year under the name "Turbo Hydra-Matic" in Cadillacs and "Super Turbine" in Buicks. The following year, application expanded to Oldsmobile and Pontiac and to some full-sized Chevrolets. Many of the Buick, Cadillac, and Oldsmobile THM400s produced between 1964-67 were equipped with a "Switch-Pitch" torque converter with a variable-pitch stator, which is sought after by collectors and drag racers. These can be identified outside the vehicle by a narrow front pump spline. Externally the switch pitch version has two electrical connections, where the non-switch pitch THM400 has only one. GM used a Switch Pitch torque converter in the Buick twin turbine Dynaflow transmission between 1955–1963 and the Super Turbine 300 two speed transmissions used by Oldsmobile, Pontiac, and Buick divisions between 1964–1967. This transmission is identified by the "Park R N D L2 L1" selector quadrant. The switch pitch is not the only THM400 that utilizes an external 2 prong connector. Other units to include the 2 prong connectors had an internal pressure switch that was used to control spark timing retard. All THM400 units had a 32 spline output shaft with the exception of the THM375 that used a 27 spline output.
A variant of the THM400 known as a THM375 is a THM400 with a mid length 27 spline output shaft that mates to the smaller THM350 27 spline drive shaft yoke. It can be identified by "375-THM" cast into the tailhousing. Internally the clutch packs originally had fewer friction plates. THM375s were found in some 1971-76 Buick Lesabres and Oldsmobile Delta 88s with the 5.7 liter V-8. Somewhere in the Mid-80's Chevrolet C10 Pickups could also come equipped with a THM375. It is a THM400 Chevrolet bolt pattern case that has a longer 27 spline output shaft and matching extension housing with "TH375" cast into the housing. Some "Heavy Duty" THM350s were also designated THM375-B. Another variant is the 3L80HD, often referred to as a Turbo 475. The 3L80HD has a straight-cut planetary gear set. There is no externally visible way to determine whether the transmission contains the straight-cut planetary gear set. The THM425 front wheel drive transmission shares almost all its internal parts with the THM400. Checker Motors Corporation Motor Company used the Chevrolet version of the THM400 for its "A" series taxi and Marathon models until the end of production in 1982.
By 1980, the relatively heavy THM400 was being phased out of usage in passenger cars in response to demand for improved fuel economy. The THM 400 was utilized in the C- and K-series Chevrolet/GMC pickups and G-series vans until 1990 when GM switched over to the 4L80E. Today, the United States Army HMMWV is the only vehicle using the THM400. The civilian Hummer H1 originally had the 3L80s, but the current model has had a 4L80E since the mid-1990s.
Through the end of the '70s substantially more CBOP bellhousing THM400s were produced than any other THM400. Chevrolet bellhousing THM400s, while not rare, can be hard to find and are, as a result, usually more expensive to buy Chevrolet/GMC trucks and vans - when used with passenger cars it was usually coupled to a Mark IV engine or some high performance small blocks. The THM400 was never produced with a multicase bell housing.
Other auto manufacturers have used the THM400 and its 4L80E successor, including Ferrari ; Jaguar/Daimler and their Daimler stable mates; Rolls-Royce ; the Nissan Prince Royal; AM General; and Jeep. Early Jeep THM400s used an adapter between the engine and transmission bell housing while later models had an AMC specific housing - which bolted to its inline six and V8. Though identical except for the bell housing pattern used through the '60s and ending in 1979 the THM400 was mated to the Dana model 18,20 and was the only transmission used with the Borg-Warner 1305/1339 all-wheel-drive transfer case used only in Jeeps, It has been known to adapt a THM400 to other engines using adapters.
THM400 transmissions are very popular in automotive competition due to their great strength. Much of this strength comes from the use of a cast iron center support to suspend the transmission's concentric shafts that join the clutch assemblies to the gear train. The center support, which is splined to the interior of the transmission's case, also provides a robust reaction point for first gear. Since the first gear reactive force is evenly distributed around the periphery of the case, the types of mechanical failures that have plagued other competition transmissions are rare.
The THM400 was the first three-speed, Simpson-geared automatic to use overrunning clutches for both first and second gear reaction, a feature that eliminated the need to coordinate the simultaneous release of a band and application of a clutch to make the 2-3 gear change. Owing to this feature, as well as the use of a large, multi-plate clutch to provide second gear reaction, the THM400 is able to withstand very high input torque and an enormous number of shifting cycles, as would be encountered in frequent stop-and-go driving. As a result, it has met with considerable success in commercial vehicle applications.
For 1987, GM changed the nomenclature of their Turbo Hydramatic transmissions — the THM400 was renamed '3L80'. The 3L80HD was introduced in 1987 as the HD unit used in passenger trucks. In 1991, a four-speed overdrive version, the 4L80-E, replaced the THM400 in Chevrolet/GMC pickups, vans, SUVs, and commercial vehicles. The 4L80E was the first Hydramatic to incorporate electronic controls — almost all of the THM400/3L80/3L80HD's components are interchangeable.
Transmission fluid cooler line connections are found on the right-hand side of the THM400. The lower connection is the cooler feed, and the upper connection is the return. The case is tapped for either self-sealing 1/4"NPT fittings, or 1/2"UNF fittings with a washer seal. 5/16" or 3/8" rigid coolant lines are generally connected via appropriate double-flared adapters.
Four-wheel drive truck applications used 3 various shorter output shafts that coupled with a female transfer case input shaft. Early transfer cases mated directly to the THM400 with a cast-iron adapter, usually a vertical oval shape. Later models used a circular style iron adapter which is generally considered the stronger of the two. The shortest was used with the NP203 transfer case.
GearRatio
12.48:1
21.48:1
31.00:1
R2.07:1

THM350

The Turbo Hydra-matic 350 was first used in 1969 model cars. It was developed jointly by Buick and Chevrolet to replace the two-speed Super Turbine 300 and aluminum-case Powerglide transmissions. So, although it carries the Turbo Hydra-matic name, the Hydra-matic Division of General Motors had little, if anything, to do with its design. The 350 and its 250, 250C, 350C and 375B derivatives have been manufactured by Buick in its Flint, Michigan plant, and by Chevrolet in Toledo and Parma, Ohio and Windsor, Ontario.
The THM350 was also regarded as a 'three speed Powerglide' and during its development, was generally called this. Although it uses the same torque converter as the THM400 it has a familial resemblance to the 1962-73 aluminum Powerglide from Chevrolet and was largely derived from the Chevrolet design. An important difference in the THM350 compared to the THM400 is that there is no fixed center support midway through the geartrain; this difference in layout would have permitted the THM350 to be adapted to the Corvair where the drive and driven ends are the same, but this feature was not exploited. Air-cooled versions of the THM350 appeared mid-1972 in the Chevrolet Vega and Nova 6.
One THM350 weak point was excessive end-play between the pump and center support and resulting wobble of the direct clutch drum due to both the end play and use of a relatively narrow bushing in the drum. This weak point can be addressed by using an extra thrust washer between the planetary gear and direct clutch to remove the end play and using a wider aftermarket bushing in the direct clutch drum. Another weak point is the relatively thin center support and the lightweight matching splines in the case. This weakness can be addressed by using an inexpensive aftermarket case saver kit.
Four-wheel drive truck applications for the THM350 used an iron adapter that mated it to the transfer case directly, similar to the THM400. The THM350 adapter was cast iron and used a sliding sleeve to couple the transmission output shaft to the transfer case input shaft with a steel coupler sleeve that was splined to accept both shafts and couple them together. An internal snap ring inside the coupler sleeve controlled the sleeve's position on the shafts, with circular seals in the adapter sealing the transmission from the transfer case.
For the 1981 model year, a lock-up torque converter was introduced which coincided with the new EMC control of most GM cars; this version is the THM350-C, which was phased out in 1984 in GM passenger cars for the 700R4. Chevrolet/GMC trucks and vans used the THM350-C until 1986. The lock-up torque converter was unpopular with transmission builders B&M Racing once marketed a conversion kit for THM350-Cs during the early 1980s until the advent of high stall lock-up torque converters when its overdrive counterpart were modified. The standard TH350 is still very popular in drag racing.

THM250

The THM250 is a derivative of the THM350 and was introduced for 1974 in Chevrolets as a Powerglide replacement. Internally, the THM250 is a THM350 without the intermediate clutch pack and with a band adjuster similar to the Powerglide. The THM250 was usually coupled to smaller displacement engines - the largest a third generation Chevrolet inline six found in the Nova and Camaro. During the 1976 model year the THM250 was phased out of production, replaced with the lighter duty THM200. It was later reintroduced in 1979 as the THM250-C in the wake of the failure-prone THM200/200C - the later 250C was further lightened with the use of a sun gear shell used with the THM350 but with 3 holes to reduce rotating mass and the low/reverse piston with 8 cutouts.
GearRatio
12.52:1
21.52:1
31.00:1
R2.07:1

THM200

After the 1973 OPEC oil embargo, GM developed a lighter-duty version of the THM350 with lightened materials — primarily alloys in place of ferrous materials — the Turbo-Hydramatic 200. The THM-200 was first used in 1976 models including GM's T-cars, X-cars, and some Isuzu automobiles. However, this transmission was notorious for its failure rate when used behind too large an engine - the largest being the Oldsmobile 5.7 L diesel. No multicase bellhousings were used - bellhousing patterns included Chevrolet V8, Buick-Oldsmobile-Pontiac, Vega 4, GM 60 degree pattern, and Isuzu G engine.
It was GM's first transmission which used a throttle valve cable controlling the shift points and part throttle kickdown. This setup was later incorporated into the THM700R4.
Starting with the 1979 model year, vehicles which had the THM-200/200C as standard equipment were optioned with the THM250-C, which is a THM-350 without the intermediate clutch pack along with an adjustable band similar to the Chevrolet Powerglide. Also in the 1979 model year, the THM-200 received a lockup torque converter, and some internal components were later shared with the Turbo-Hydramatic 200-4R. The low/reverse sprag assembly was also shared with the 1988-04 Chrysler Torqueflite 904 and its derivatives e.g. the A500 and 42RE. THM200/200Cs were produced until 1987.
GearRatio
12.74:1
21.57:1
31.00:1
R2.07:1

THM200-4R

For the 1981 model year, the 200-4R was introduced. The components which were prone to failure in the THM200 were improved, and in the later 1980s this transmission was used with high-power applications — primarily the Buick Grand National and the 1989 Pontiac Firebird Trans Am Indy 500 Pace cars. The 200-4R was configured with several different torque converters depending on the vehicle application.
Unlike the 700R4, most 200-4Rs have a multicase bellhousing for use with Chevrolet, Buick/Olds/Pontiac, and Cadillac engines. However, 200-4Rs share mounting locations with the TH-400. Since the external dimensions are similar to the TH-350, 200-4Rs are often swapped in place of TH-350s in older vehicles to provide an overdrive gear. Early models had a "PRND321" shift indicator, while later models used "PRND21," with the left D identified as the overdrive gear by a square or oval ring.
The THM200-4R can be found in the following vehicles:
The THM200-4R was phased out after 1990; its final usage was in the GM B-body vehicles.
GearRatio
12.74:1
21.57:1
31.00:1
40.67:1
R2.07:1

THM700R4 / 4L60 / 4L60E / 4L65E / 4L70E

The four-speed Turbo Hydra-Matic 700R4 was introduced for the 1982 model year for use in Chevrolet/GMC vehicles.
In 1990, the Turbo Hydra-Matic 700R4 was renamed the 4L60. Under the new designation, the "4" stands for the number of forward gears, the "L" for longitudinal applications, and the "60" is the strength rating. "60" is the relative torque value. For example, 80 is stronger than 60, which is stronger than 40, etc. A 4L80-E can handle more torque than a 4L60-E. The "E" denotes electronically controlled shifting. The 4L60 however is hydraulically shifted based on governor pressure and throttle valve cable position. 1992 was the last year of widespread usage of the 700R4. The 1993 Camaro, Corvette and Typhoon were equipped with the last production 700R4. The last design change of the 700R4 was an added checkball to the valve body. In 1992 electronic controls were added, and it became the 4L60-E. The 4L60E is not easily swapped with the 4L60, as the 4L60E depends on a powertrain control module to shift. The 4L60E went into service in trucks, vans, and SUVs in 1993 and in all RWD passenger cars in 1994. In 2001, an updated version — the 4L65-E, was introduced. Five-pinion planetaries, along with a strength-improved output shaft, were improved to withstand the 300+ lb·ft of torque of the 6.0 Vortec engine.
The 4L70E transmission is the same as a 4L65E with a speed sensor located in the pump.

700R4 / 4L60 / 4L60E / 4L65E / 4L70E / technical description

The Turbo Hydra-Matic 700R4 can be identified by an oil pan number six shown at .
The tailshaft housing is held onto the main case by four bolts, and uses a square-cut o-ring seal, and not a gasket. The typical width of this transmission where it bolts to the engine is overall. From the engine/trans mating surface to the cross member mount bolt is, and engine/trans surface to output shaft housing mating surface is overall, with the tail shaft housing typically measuring. External dimensions are similar to a THM350 with a 9-inch tailhousing found in Chevrolet/GMC long wheelbase truck/vans and 1971-76 B-bodies.
Transmission fluid cooler lines on the 700R4 the bottom fitting on the right side of the transmission is the "out" line to the cooler and the top fitting is for the return line from the cooler. These fittings are pipe thread, and can include an adapter from the factory for threaded steel lines in a SAE size. 4L60Es manufactured after 1995 use snap-in connections instead of threaded. The original version of the transmission had a 27-spline input shaft which was a common failure point. In 1984, the 700R4 designed for use behind Chevrolet small block V8s received a 30-spline input shaft similar to those found on TH400 transmissions and which also used a different torque converter than its 2.8 V6 and 2.2 L4 engines. Between 1984–1987, internal components, from the ring gear to the oil pump housing, were updated, ending with the auxiliary valve body for 700s manufactured after October 1986.
In 1995, the 4L60E received a PWM-controlled lockup converter. The early designs simple on or off lockup function while the later design can variably lock as to not feel the lock up occur. GM added a fifth solenoid to the valve body, called the PWM solenoid. In 1996, GM introduced a redesigned 4L60E transmission case that incorporated a bolt-on bellhousing and a six-bolt tail housing. This two-piece case style was first seen in 1996 and up model S-10 Blazer, S-10 pickup, GMC Jimmy, and GMC Sonoma with the 4.3 L engine. The majority of 1998 and later applications of the 4L60E were two-piece cases. Both transmissions are the same internally. The non-PWM style 4L60Es are not interchangeable with PWM-style 4L60Es. Also in 1996, GM changed the 3-2 solenoid to a different style which makes it not interchangeable with any previous models. For the model year 1996 GM trucks, there were two versions of the 4L60E: one had a bolt-on bellhousing, the other did not. The bolt-on bellhousings used on the 4.3 L V6 and 1996-2002 GEN I+ versions of the small-block Chevrolet V8 used the same bellhousing, while the LSx engines used a longer one to accommodate a redesigned torque converter with a longer pilot nose.
GearRatio
13.059:1
21.625:1
31.00:1
40.696:1
R2.29:1

700R4 / 4L60 / 4L60E / 4L65E /4L70E applications