Transverse isotropy


A transversely isotropic material is one with physical properties that are symmetric about an axis that is normal to a plane of isotropy. This transverse plane has infinite planes of symmetry and thus, within this plane, the material properties are the same in all directions. Hence, such materials are also known as "polar anisotropic" materials. In geophysics, vertically transverse isotropy is also known as radial anisotropy.
This type of material exhibits hexagonal symmetry, so the number of independent constants in the elasticity tensor are reduced to 5. The tensors of electrical resistivity, permeability, etc. have two independent constants.

Example of transversely isotropic materials

An example of a transversely isotropic material is the so-called on-axis unidirectional fiber composite lamina where the fibers are circular in cross section. In a unidirectional composite, the plane normal to the fiber direction can be considered as the isotropic plane, at long wavelengths of excitation. In the figure to the right, the fibers would be aligned with the axis, which is normal to the plane of isotropy.
In terms of effective properties, geological layers of rocks are often interpreted as being transversely isotropic. Calculating the effective elastic properties of such layers in petrology has been coined Backus upscaling, which is described below.

Material symmetry matrix

The material matrix has a symmetry with respect to a given orthogonal transformation if it does not change when subjected to that transformation.
For invariance of the material properties under such a transformation we require
Hence the condition for material symmetry is
Orthogonal transformations can be represented in Cartesian coordinates by a matrix given by
Therefore, the symmetry condition can be written in matrix form as
For a transversely isotropic material, the matrix has the form
where the -axis is the axis of symmetry. The material matrix remains invariant under rotation by any angle about the -axis.

In physics

Linear material constitutive relations in physics can be expressed in the form
where are two vectors representing physical quantities and is a second-order material tensor. In matrix form,
Examples of physical problems that fit the above template are listed in the table below.
Problem
Electrical conductionElectric current
Electric field
Electrical conductivity
DielectricsElectrical displacement
Electric field
Electric permittivity
MagnetismMagnetic induction
Magnetic field
Magnetic permeability
Thermal conductionHeat flux
Temperature gradient
Thermal conductivity
DiffusionParticle flux
Concentration gradient
Diffusivity
Flow in porous mediaWeighted fluid velocity
Pressure gradient
Fluid permeability
ElasticityStress
Strain
Stiffness

Using in the matrix implies that. Using leads to and. Energy restrictions usually require and hence we must have. Therefore, the material properties of a transversely isotropic material are described by the matrix

In linear elasticity

Condition for material symmetry

In linear elasticity, the stress and strain are related by Hooke's law, i.e.,
or, using Voigt notation,
The condition for material symmetry in linear elastic materials is.
where

Elasticity tensor

Using the specific values of in matrix, it can be shown that the fourth-rank elasticity stiffness tensor may be written in 2-index Voigt notation as the matrix
The elasticity stiffness matrix has 5 independent constants, which are related to well known engineering elastic moduli in the following way. These engineering moduli are experimentally determined.
The compliance matrix is
where. In engineering notation,
Comparing these two forms of the compliance matrix shows us that the longitudinal Young's modulus is given by
Similarly, the transverse Young's modulus is
The inplane shear modulus is
and the Poisson's ratio for loading along the polar axis is
Here, L represents the longitudinal direction and T represents the transverse direction.

In geophysics

In geophysics, a common assumption is that the rock formations of the crust are locally polar anisotropic ; this is the simplest case of geophysical interest. Backus upscaling is often used to determine the effective transversely isotropic elastic constants of layered media for long wavelength seismic waves.
Assumptions that are made in the Backus approximation are:
For shorter wavelengths, the behavior of seismic waves is described using the superposition of plane waves. Transversely isotropic media support three types of elastic plane waves:
Solutions to wave propagation problems in such media may be constructed from these plane waves, using Fourier synthesis.

Backus upscaling (long wavelength approximation)

A layered model of homogeneous and isotropic material, can be up-scaled to a transverse isotropic medium, proposed by Backus.
Backus presented an equivalent medium theory, a heterogeneous medium can be replaced by a homogeneous one that predicts wave propagation in the actual medium. Backus showed that layering on a scale much finer than the wavelength has an impact and that a number of isotropic layers can be replaced by a homogeneous transversely isotropic medium that behaves exactly in the same manner as the actual medium under static load in the infinite wavelength limit.
If each layer is described by 5 transversely isotropic parameters, specifying the matrix
The elastic moduli for the effective medium will be
where
denotes the volume weighted average over all layers.
This includes isotropic layers, as the layer is isotropic if, and.

Short and medium wavelength approximation

Solutions to wave propagation problems in linear elastic transversely isotropic media can be constructed by superposing solutions for the quasi-P wave, the quasi S-wave, and a S-wave polarized orthogonal to the quasi S-wave.
However, the equations for the angular variation of velocity are algebraically complex and the plane-wave velocities are functions of the propagation angle are. The direction dependent wave speeds for elastic waves through the material can be found by using the Christoffel equation and are given by
where is the angle between the axis of symmetry and the wave propagation direction, is mass density and the are elements of the elastic stiffness matrix. The Thomsen parameters are used to simplify these expressions and make them easier to understand.

Thomsen parameters

Thomsen parameters are dimensionless combinations of elastic moduli that characterize transversely isotropic materials, which are encountered, for example, in geophysics. In terms of the components of the elastic stiffness matrix, these parameters are defined as:
where index 3 indicates the axis of symmetry . These parameters, in conjunction with the associated P wave and S wave velocities, can be used to characterize wave propagation through weakly anisotropic, layered media. Empirically, the Thomsen parameters for most layered rock formations are much lower than 1.
The name refers to Leon Thomsen, professor of geophysics at the University of Houston, who proposed these parameters in his 1986 paper "Weak Elastic Anisotropy".

Simplified expressions for wave velocities

In geophysics the anisotropy in elastic properties is usually weak, in which case \delta, \gamma, \epsilon \ll 1. When the exact expressions for the wave velocities above are linearized in these small quantities, they simplify to
where
are the P and S wave velocities in the direction of the axis of symmetry . Note that may be further linearized, but this does not lead to further simplification.
The approximate expressions for the wave velocities are simple enough to be physically interpreted, and sufficiently accurate for most geophysical applications. These expressions are also useful in some contexts where the anisotropy is not weak.