Tractive force


As used in mechanical engineering, the term tractive force can either refer to the total traction a vehicle exerts on a surface, or the amount of the total traction that is parallel to the direction of motion.
In railway engineering, the term tractive effort is often used synonymously with tractive force to describe the pulling or pushing capability of a locomotive. In automotive engineering, the terms are distinctive: tractive effort is generally higher than tractive force by the amount of rolling resistance present, and both terms are higher than the amount of drawbar pull by the total resistance present. The published tractive force value for any vehicle may be theoretical—that is, calculated from known or implied mechanical properties—or obtained via testing under controlled conditions. The discussion herein covers the term's usage in mechanical applications in which the final stage of the power transmission system is one or more wheels in frictional contact with a roadway or railroad track.

Defining tractive effort

The term tractive effort is often qualified as starting tractive effort, continuous tractive effort and maximum tractive effort. These terms apply to different operating conditions, but are related by common mechanical factors: input torque to the driving wheels, the wheel diameter, coefficient of friction between the driving wheels and supporting surface, and the weight applied to the driving wheels. The product of μ and m is the factor of adhesion, which determines the maximum torque that can be applied before the onset of wheelspin or wheelslip.
Tractive effort inversely varies with speed at any given level of available power. Continuous tractive effort is often shown in graph form at a range of speeds as part of a tractive effort curve.
Vehicles having a hydrodynamic coupling, hydrodynamic torque multiplier or electric motor as part of the power transmission system may also have a maximum continuous tractive effort rating, which is the highest tractive force that can be produced for a short period of time without causing component harm. The period of time for which the maximum continuous tractive effort may be safely generated is usually limited by thermal considerations. such as temperature rise in a traction motor.

Tractive effort curves

Specifications of locomotives often include tractive effort curves, showing the relationship between tractive effort and velocity.
The shape of the graph is shown at right. The line AB shows operation at the maximum tractive effort, the line BC shows continuous tractive effort that is inversely proportional to speed.
Tractive effort curves often have graphs of rolling resistance superimposed on them—the intersection of the rolling resistance graph and tractive effort graph gives the maximum velocity.

Rail vehicles

In order to start a train and accelerate it to a given speed, the locomotive must develop sufficient tractive force to overcome the train's drag, which is a combination of inertia, axle bearing friction, the friction of the wheels on the rails, and the force of gravity if on a grade. Once in motion, the train will develop additional drag as it accelerates due to aerodynamic forces, which increase with the square of the speed. Drag may also be produced at speed due to truck hunting, which will increase the rolling friction between wheels and rails. If acceleration continues, the train will eventually attain a speed at which the available tractive force of the locomotive will exactly offset the total drag, causing acceleration to cease. This top speed will be increased on a downgrade due to gravity assisting the motive power, and will be decreased on an upgrade due to gravity opposing the motive power.
Tractive effort can be theoretically calculated from a locomotive's mechanical characteristics, or by actual testing with drawbar strain sensors and a dynamometer car. Power at rail is a railway term for the available power for traction, that is, the power that is available to propel the train.

Steam locomotives

An estimate for the tractive effort of a single cylinder steam locomotive can be obtained from the cylinder pressure, cylinder bore, stroke of the piston and the diameter of the wheel. The torque developed by the linear motion of the piston depends on the angle that the driving rod makes with the tangent of the radius on the driving wheel. For a more useful value an average value over the rotation of the wheel is used. The driving force is the torque divided by the wheel radius.
As an approximation, the following formula can be used :
where
The constant 0.85 was the Association of American Railroads standard for such calculations, and overestimated the efficiency of some locomotives and underestimated that of others. Modern locomotives with roller bearings were probably underestimated.
European designers used a constant of 0.6 instead of 0.85, so the two cannot be compared without a conversion factor. In Britain main-line railways generally used a constant of 0.85 but builders of industrial locomotives often used a lower figure, typically 0.75.
The constant c also depends on the cylinder dimensions and the time at which the steam inlet valves are open; if the steam inlet valves are closed immediately after obtaining full cylinder pressure the piston force can be expected to have dropped to less than half the initial force. giving a low c value. If the cylinder valves are left open for longer the value of c will rise nearer to one.
;Three or four cylinders
The result should be multiplied by 1.5 for a three-cylinder locomotive and by two for a four-cylinder locomotive.
Alternatively, tractive effort of all 'simple' locomotives can be calculated thus:
where
;Multiple cylinders
For other numbers and combinations of cylinders, including double and triple expansion engines the tractive effort can be estimated by adding the tractive efforts due to the individual cylinders at their respective pressures and cylinder strokes.

Values and comparisons for steam locomotives

Tractive effort is the figure often quoted when comparing the powers of steam locomotives, but is misleading because tractive effort shows the ability to start a train, not the ability to haul it. Possibly the highest tractive effort ever claimed was for the Virginian Railway's 2-8-8-8-4 Triplex locomotive, which in simple expansion mode had a calculated starting T.E. of 199,560 lbf —but the boiler could not produce enough steam to haul at speeds over 5 mph.
Of more successful steam locomotives, those with the highest rated starting tractive effort were the Virginian Railway AE-class 2-10-10-2s, at 176,000 lbf in simple-expansion mode. The Union Pacific Big Boys had a starting T.E. of 135,375 lbf ; the Norfolk & Western's Y5, Y6, Y6a, and Y6b class 2-8-8-2s had a starting T.E. of 152,206 lbf in simple expansion mode ; and the Pennsylvania Railroad's freight Duplex Q2 attained 114,860 lbf —the highest for a rigid framed locomotive. Later two-cylinder passenger locomotives were generally 40,000 to 80,000 lbf of T.E.

Diesel and electric locomotives

For an electric locomotive or a diesel-electric locomotive, starting tractive effort can be calculated from the amount of weight on the driving wheels, combined stall torque of the traction motors, the gear ratio between the traction motors and axles, and driving wheel diameter. For a diesel-hydraulic locomotive, the starting tractive effort is affected by the stall torque of the torque converter, as well as gearing, wheel diameter and locomotive weight.
The relationship between power and tractive effort was expressed by Hay as
where
Freight locomotives are designed to produce higher maximum tractive effort than passenger units of equivalent power, necessitated by the much higher weight that is typical of a freight train. In modern locomotives, the gearing between the traction motors and axles is selected to suit the type of service in which the unit will be operated. As traction motors have a maximum speed at which they can rotate without incurring damage, gearing for higher tractive effort is at the expense of top speed. Conversely, the gearing used with passenger locomotives favors speed over maximum tractive effort.
Electric locomotives with monomotor bogies are sometimes fitted with two-speed gearing. This allows higher tractive effort for hauling freight trains but at reduced speed. Examples include the SNCF classes BB 8500 and BB 25500.