Storage virtualization


In computer science, storage virtualization is "the process of presenting a logical view of the physical storage resources to" a host computer system, "treating all storage media in the enterprise as a single pool of storage."
A "storage system" is also known as a storage array, disk array, or filer. Storage systems typically use special hardware and software along with disk drives in order to provide very fast and reliable storage for computing and data processing. Storage systems are complex, and may be thought of as a special purpose computer designed to provide storage capacity along with advanced data protection features. Disk drives are only one element within a storage system, along with hardware and special purpose embedded software within the system.
Storage systems can provide either block accessed storage, or file accessed storage. Block access is typically delivered over Fibre Channel, iSCSI, SAS, FICON or other protocols. File access is often provided using NFS or SMB protocols.
Within the context of a storage system, there are two primary types of virtualization that can occur:

Address space remapping

Virtualization of storage helps achieve location independence by abstracting the physical location of the data. The virtualization system presents to the user a logical space for data storage and handles the process of mapping it to the actual physical location.
It is possible to have multiple layers of virtualization or mapping. It is then possible that the output of one layer of virtualization can then be used as the input for a higher layer of virtualization. Virtualization maps space between back-end resources, to front-end resources. In this instance, "back-end" refers to a logical unit number that is not presented to a computer, or host system for direct use. A "front-end" LUN or volume is presented to a host or computer system for use.
The actual form of the mapping will depend on the chosen implementation. Some implementations may limit the granularity of the mapping which may limit the capabilities of the device. Typical granularities range from a single physical disk down to some small subset of the physical disk.
In a block-based storage environment, a single block of information is addressed using a LUN identifier and an offset within that LUN known as a logical block addressing.

Meta-data

The virtualization software or device is responsible for maintaining a consistent view of all the mapping information for the virtualized storage. This mapping information is often called meta-data and is stored as a mapping table.
The address space may be limited by the capacity needed to maintain the mapping table. The level of granularity, and the total addressable space both directly impact the size of the meta-data, and hence the mapping table. For this reason, it is common to have trade-offs, between the amount of addressable capacity and the granularity or access granularity.
One common method to address these limits is to use multiple levels of virtualization. In several storage systems deployed today, it is common to utilize three layers of virtualization.
Some implementations do not use a mapping table, and instead calculate locations using an algorithm. These implementations utilize dynamic methods to calculate the location on access, rather than storing the information in a mapping table.

I/O redirection

The virtualization software or device uses the meta-data to re-direct I/O requests. It will receive an incoming I/O request containing information about the location of the data in terms of the logical disk and translates this into a new I/O request to the physical disk location.
For example, the virtualization device may :
Most implementations allow for heterogeneous management of multi-vendor storage devices within the scope of a given implementation's support matrix. This means that the following capabilities are not limited to a single vendor's device and are in fact possible across different vendors' devices.

Replication

Data replication techniques are not limited to virtualization appliances and as such are not described here in detail. However most implementations will provide some or all of these replication services.
When storage is virtualized, replication services must be implemented above the software or device that is performing the virtualization. This is true because it is only above the virtualization layer that a true and consistent image of the logical disk can be copied. This limits the services that some implementations can implement or makes them seriously difficult to implement. If the virtualization is implemented in the network or higher, this renders any replication services provided by the underlying storage controllers useless.
The physical storage resources are aggregated into storage pools, from which the logical storage is created. More storage systems, which may be heterogeneous in nature, can be added as and when needed, and the virtual storage space will scale up by the same amount. This process is fully transparent to the applications using the storage infrastructure.

Disk management

The software or device providing storage virtualization becomes a common disk manager in the virtualized environment. Logical disks are created by the virtualization software or device and are mapped to the required host or server, thus providing a common place or way for managing all volumes in the environment.
Enhanced features are easy to provide in this environment:

Non-disruptive data migration

One of the major benefits of abstracting the host or server from the actual storage is the ability to migrate data while maintaining concurrent I/O access.
The host only knows about the logical disk and so any changes to the meta-data mapping is transparent to the host. This means the actual data can be moved or replicated to another physical location without affecting the operation of any client. When the data has been copied or moved, the meta-data can simply be updated to point to the new location, therefore freeing up the physical storage at the old location.
The process of moving the physical location is known as data migration. Most implementations allow for this to be done in a non-disruptive manner, that is concurrently while the host continues to perform I/O to the logical disk.
The mapping granularity dictates how quickly the meta-data can be updated, how much extra capacity is required during the migration, and how quickly the previous location is marked as free. The smaller the granularity the faster the update, less space required and quicker the old storage can be freed up.
There are many day to day tasks a storage administrator has to perform that can be simply and concurrently performed using data migration techniques.
Utilization can be increased by virtue of the pooling, migration, and thin provisioning services. This allows users to avoid over-buying and over-provisioning storage solutions. In other words, this kind of utilization through a shared pool of storage can be easily and quickly allocated as it is needed to avoid constraints on storage capacity that often hinder application performance.
When all available storage capacity is pooled, system administrators no longer have to search for disks that have free space to allocate to a particular host or server. A new logical disk can be simply allocated from the available pool, or an existing disk can be expanded.
Pooling also means that all the available storage capacity can potentially be used. In a traditional environment, an entire disk would be mapped to a host. This may be larger than is required, thus wasting space. In a virtual environment, the logical disk is assigned the capacity required by the using host.
Storage can be assigned where it is needed at that point in time, reducing the need to guess how much a given host will need in the future. Using Thin Provisioning, the administrator can create a very large thin provisioned logical disk, thus the using system thinks it has a very large disk from day one.

Fewer points of management

With storage virtualization, multiple independent storage devices, even if scattered across a network, appear to be a single monolithic storage device and can be managed centrally.
However, traditional storage controller management is still required. That is, the creation and maintenance of RAID arrays, including error and fault management.

Risks

Backing out a failed implementation

Once the abstraction layer is in place, only the virtualizer knows where the data actually resides on the physical medium. Backing out of a virtual storage environment therefore requires the reconstruction of the logical disks as contiguous disks that can be used in a traditional manner.
Most implementations will provide some form of back-out procedure and with the data migration services it is at least possible, but time consuming.

Interoperability and vendor support

Interoperability is a key enabler to any virtualization software or device. It applies to the actual physical storage controllers and the hosts, their operating systems, multi-pathing software and connectivity hardware.
Interoperability requirements differ based on the implementation chosen. For example, virtualization implemented within a storage controller adds no extra overhead to host based interoperability, but will require additional support of other storage controllers if they are to be virtualized by the same software.
Switch based virtualization may not require specific host interoperability — if it uses packet cracking techniques to redirect the I/O.
Network based appliances have the highest level of interoperability requirements as they have to interoperate with all devices, storage and hosts.

Complexity

Complexity affects several areas :
Information is one of the most valuable assets in today's business environments. Once virtualized, the meta-data are the glue in the middle. If the meta-data are lost, so is all the actual data as it would be virtually impossible to reconstruct the logical drives without the mapping information.
Any implementation must ensure its protection with appropriate levels of back-ups and replicas. It is important to be able to reconstruct the meta-data in the event of a catastrophic failure.
The meta-data management also has implications on performance. Any virtualization software or device must be able to keep all the copies of the meta-data atomic and quickly updateable. Some implementations restrict the ability to provide certain fast update functions, such as point-in-time copies and caching where super fast updates are required to ensure minimal latency to the actual I/O being performed.

Performance and scalability

In some implementations the performance of the physical storage can actually be improved, mainly due to caching. Caching however requires the visibility of the data contained within the I/O request and so is limited to in-band and symmetric virtualization software and devices. However these implementations also directly influence the latency of an I/O request, due to the I/O having to flow through the software or device. Assuming the software or device is efficiently designed this impact should be minimal when compared with the latency associated with physical disk accesses.
Due to the nature of virtualization, the mapping of logical to physical requires some processing power and lookup tables. Therefore, every implementation will add some small amount of latency.
In addition to response time concerns, throughput has to be considered. The bandwidth into and out of the meta-data lookup software directly impacts the available system bandwidth. In asymmetric implementations, where the meta-data lookup occurs before the information is read or written, bandwidth is less of a concern as the meta-data are a tiny fraction of the actual I/O size. In-band, symmetric flow through designs are directly limited by their processing power and connectivity bandwidths.
Most implementations provide some form of scale-out model, where the inclusion of additional software or device instances provides increased scalability and potentially increased bandwidth. The performance and scalability characteristics are directly influenced by the chosen implementation.

Implementation approaches

Host-based virtualization requires additional software running on the host, as a privileged task or process. In some cases volume management is built into the operating system, and in other instances it is offered as a separate product. Volumes presented to the host system are handled by a traditional physical device driver. However, a software layer resides above the disk device driver intercepts the I/O requests, and provides the meta-data lookup and I/O mapping.
Most modern operating systems have some form of logical volume management built-in, that performs virtualization tasks.
Note: Host based volume managers were in use long before the term storage virtualization had been coined.
Pros
it uses to store a data in virtually an access it virtually
Cons
Like host-based virtualization, several categories have existed for years and have only recently been classified as virtualization. Simple data storage devices, like single hard disk drives, do not provide any virtualization. But even the simplest disk arrays provide a logical to physical abstraction, as they use RAID schemes to join multiple disks in a single array.
Advanced disk arrays often feature cloning, snapshots and remote replication. Generally these devices do not provide the benefits of data migration or replication across heterogeneous storage, as each vendor tends to use their own proprietary protocols.
A new breed of disk array controllers allows the downstream attachment of other storage devices. For the purposes of this article we will only discuss the later style which do actually virtualize other storage devices.
Concept
A primary storage controller provides the services and allows the direct attachment of other storage controllers. Depending on the implementation these may be from the same or different vendors.
The primary controller will provide the pooling and meta-data management services. It may also provide replication and migration services across those controllers which it is.
Pros
Storage virtualization operating on a network based device and using iSCSI or FC Fibre channel networks to connect as a SAN. These types of devices are the most commonly available and implemented form of virtualization.
The virtualization device sits in the SAN and provides the layer of abstraction between the hosts performing the I/O and the storage controllers providing the storage capacity.
Pros
There are two commonly available implementations of network-based storage virtualization, appliance-based and switch-based. Both models can provide the same services, disk management, metadata lookup, data migration and replication. Both models also require some processing hardware to provide these services.
Appliance based devices are dedicated hardware devices that provide SAN connectivity of one form or another. These sit between the hosts and storage and in the case of in-band appliances can provide all of the benefits and services discussed in this article. I/O requests are targeted at the appliance itself, which performs the meta-data mapping before redirecting the I/O by sending its own I/O request to the underlying storage. The in-band appliance can also provide caching of data, and most implementations provide some form of clustering of individual appliances to maintain an atomic view of the metadata as well as cache data.
Switch based devices, as the name suggests, reside in the physical switch hardware used to connect the SAN devices. These also sit between the hosts and storage but may use different techniques to provide the metadata mapping, such as packet cracking to snoop on incoming I/O requests and perform the I/O redirection. It is much more difficult to ensure atomic updates of metadata in a switched environment and services requiring fast updates of data and metadata may be limited in switched implementations.

In-band vs. out-of-band

In-band, also known as symmetric, virtualization devices actually sit in the data path between the host and storage. All I/O requests and their data pass through the device. Hosts perform I/O to the virtualization device and never interact with the actual storage device. The virtualization device in turn performs I/O to the storage device. Caching of data, statistics about data usage, replications services, data migration and thin provisioning are all easily implemented in an in-band device.
Out-of-band, also known as asymmetric, virtualization devices are sometimes called meta-data servers. These devices only perform the meta-data mapping functions. This requires additional software in the host which knows to first request the location of the actual data. Therefore, an I/O request from the host is intercepted before it leaves the host, a meta-data lookup is requested from the meta-data server which returns the physical location of the data to the host. The information is then retrieved through an actual I/O request to the storage. Caching is not possible as the data never passes through the device.

File based virtualization

A synonym used for NAS virtualization.