Solar updraft tower


The solar updraft tower is a design concept for a renewable-energy power plant for generating electricity from low temperature solar heat. Sunshine heats the air beneath a very wide greenhouse-like roofed collector structure surrounding the central base of a very tall chimney tower. The resulting convection causes a hot air updraft in the tower by the chimney effect. This airflow drives wind turbines, placed in the chimney updraft or around the chimney base, to produce electricity.
As of mid 2018, although several prototype models have been built, no full-scale practical units are in operation. Scaled-up versions of demonstration models are planned to generate significant power. They may also allow development of other applications, such as to agriculture or horticulture, to water extraction or distillation, or to improvement of urban air pollution.
Commercial investment may have been discouraged by the high initial cost of building a very large novel structure, the large land area required and by the risk of investment. However, there is renewed interest in solar updraft towers, especially in sunny remote areas. A few prototypes have recently been built, and projects are proposed for parts of Africa, the US and Australia.
In 2014, National Geographic published a popular update, including an interview with an informed engineering proponent. A solar updraft tower power plant can generate electricity from the low temperature atmospheric heat gradient between ground or surface level and structurally reachable altitude. Functional or mechanical feasibility is now less of an issue than capitalisation.
A comprehensive review of theoretical and experimental aspects of solar updraft tower power plant development is available, recommending commercial development.

Design

Power output depends primarily on two factors: collector area and chimney height. A larger area collects and warms a greater volume of air to flow up the chimney; collector areas as large as in diameter have been discussed. A larger chimney height increases the pressure difference via the stack effect; chimneys as tall as have been discussed.
Heat is stored inside the collector area allowing SUTs to operate 24 hours a day. The ground beneath the solar collector, water in bags or tubes, or a saltwater thermal sink in the collector could add thermal capacity and inertia to the collector. Humidity of the updraft and condensation in the chimney could increase the energy flux of the system.
Turbines with a horizontal axis can be installed in a ring around the base of the tower, as once planned for an Australian project and seen in the diagram above; or—as in the prototype in Spain—a single vertical axis turbine can be installed inside the chimney.
A near negligible amount of Carbon dioxide is produced as part of operations, while construction material manufacturing can create emissions. Net energy payback is estimated to be 2–3 years.
Since solar collectors occupy significant amounts of land, deserts and other low-value sites are most likely. Improvements in the solar heat collection efficiency by using unglazed transpired collector can significantly reduce the land required for the solar array.
A small-scale solar updraft tower may be an attractive option for remote regions in developing countries. The relatively low-tech approach could allow local resources and labour to be used for construction and maintenance.
Locating a tower at high latitudes could produce up to 85 percent of the output of a similar plant located closer to the equator, if the collection area is sloped significantly toward the equator. The sloped collector field, which also functions as a chimney, is built on suitable mountainsides, with a short vertical chimney on the mountaintop to accommodate the vertical axis air turbine. The results showed that solar chimney power plants at high latitudes may have satisfactory thermal performance.

History

A chimney turbine was envisioned as a smoke jack, and illustrated 500 years ago by Leonardo da Vinci. An animal spitted above a fire or in an oven could be turned by a vertical axis turbine with four angled vanes in the chimney updraft.
In 1896, Mr. Alfred Rosling Bennett published the first patent describing a "Convection Mill". Even if in the title of the Patent and in the claims the word "Toy" clearly appears and even if in the overall description made inside the Patent it is evident that the idea was to produce small devices, in page 3 at lines 49-54 Bennett envisions much larger devices for bigger scale applications. A model of this "convection mill", built in 1919 by Albert H. Holmes & Son to demonstrate the phenomenon of convection currents, is on display in the Science Museum, London.
In 1903, Isidoro Cabanyes, a colonel in the Spanish army, proposed a solar chimney power plant in the magazine La energía eléctrica. Another early description was published in 1931 by German author Hanns Günther. Beginning in 1975, Robert E. Lucier applied for patents on a solar chimney electric power generator; between 1978 and 1981 patents were granted in Australia, Canada, Israel, and the US.
In 1926 Prof Engineer Bernard Dubos proposed to the French Academy of Sciences the construction of a Solar Aero-Electric Power Plant in North Africa with its solar chimney on the slope of a large mountain.
In 1982, a small-scale experimental model of a solar draft tower was built in Manzanares, Ciudad Real, 150 km south of Madrid, Spain at. The power plant operated for approximately eight years. The tower's guy-wires were not protected against corrosion and failed due to rust and storm winds. The tower blew over and was decommissioned in 1989.
Inexpensive materials were used in order to evaluate their performance. The solar tower was built of iron plating only thick under the direction of a German engineer, Jörg Schlaich. The project was funded by the German government.
The chimney had a height of and a diameter of with a collection area of and a diameter of, obtaining a maximum power output of about 50 kW. Various materials were used for testing, such as single or double glazing or plastic. One section was used as an actual greenhouse. During its operation, 180 sensors measured inside and outside temperature, humidity and wind speed data was collected on a second-by-second basis. This experimental setup did not sell energy.
In December 2010, a tower in Jinshawan in Inner Mongolia, China started operation, producing 200 kilowatts. The 1.38 billion RMB project was started in May 2009. It was intended to cover and produce 27.5 MW by 2013, but had to be scaled back. The solar chimney plant was expected to improve the climate by covering loose sand, restraining sandstorms. Critics have said that the 50m tall tower is too short to work properly and that it was a mistake to use glass in metal frames for the collector, as many of them cracked and shattered in the heat.
A proposal to construct a solar updraft tower in Fuente el Fresno, Ciudad Real, Spain, entitled Ciudad Real Torre Solar would be the first of its kind in the European Union and would stand tall, covering an area of.
It is expected to produce 40 MW. At that height, it would be nearly twice as tall as the Belmont TV Mast, which was once the tallest structure in the European Union, before being shortened by 24 meter.
In 2001, EnviroMission proposed to build a solar updraft tower power generating plant known as Solar Tower Buronga near Buronga, New South Wales. The company did not complete the project. They have plans for a similar plant in Arizona, and most recently in Texas, but there is no sign of 'breaking ground' in any of Enviromission's proposals.
In December 2011, Hyperion Energy, controlled by Western Australians Tony Sage and Dallas Dempster, was reported to be planning to build a 1-km-tall solar updraft tower near Meekatharra to supply power to Mid-West mining projects.
Based on the need for plans for long-term energy strategies, Botswana's Ministry of Science and Technology designed and built a small-scale research tower. This experiment ran from 7 October to 22 November 2005. It had an inside diameter of and a height of, manufactured from glass-reinforced polyester, with an area of approximately. The roof was made of a 5 mm thick clear glass supported by a steel framework.
In mid-2008, the Namibian government approved a proposal for the construction of a 400 MW solar chimney called the 'Greentower'. The tower is planned to be tall and in diameter, and the base will consist of a greenhouse in which cash crops can be grown.
A model solar updraft tower was constructed in Turkey as a civil engineering project. Functionality and outcomes are obscure.
A second solar updraft tower using a transpired collector is operating at Trakya University in Edirne Turkey and is being used to test various innovations in SUT designs including the ability to recover heat from photovoltaic arrays.
A grade-school pupil's home do-it-yourself SUT demonstration for a school science fair was constructed and studied in 2012, in a suburban Connecticut setting. With a 7-metre stack and 100 square metre collector, this generated a daily average 6.34 mW, from a computer fan as a turbine. Insolation and wind were the major factors on variance in output.
In Xian, central China, a 60-metre urban chimney with surrounding collector has significantly reduced urban air pollution. This demonstration project was led by Cao Junji, a chemist at the Chinese Academy of Sciences’ Key Laboratory of Aerosol Chemistry and Physics.

Efficiency

The traditional solar updraft tower has a power conversion rate considerably lower than many other designs in the solar thermal group of collectors. The low conversion rate is balanced to some extent by the lower cost per square metre of solar collection.
Model calculations estimate that a 100 MW plant would require a 1,000 m tower and a greenhouse of. A 200 MW tower with the same tower would require a collector 7 kilometres in diameter. One 200MW power station will provide enough electricity for around 200,000 typical households and will abate over 900,000 tons of greenhouse producing gases from entering the environment annually. The glazed collector area is expected to extract about 0.5 percent, or 5 W/m² of 1 kW/m², of the solar energy that falls upon it. If a transpired solar collector is used in place of the glazed collector, the efficiency is doubled. Additional efficiency improvements are possible by modifying the turbine and chimney design to increase air speed using a venturi configuration. Concentrating thermal or photovoltaic solar power plants range between 20% to 31.25% efficiency. Overall CSP/CPV efficiency is reduced because collectors do not cover the entire footprint. Without further tests, the accuracy of these calculations is uncertain. Most of the projections of efficiency, costs and yields are calculated theoretically, rather than empirically derived from demonstrations, and are seen in comparison with other collector or solar heat transducing technologies.
An innovative concept recombining a thermal power plant dry cooling tower with a solar chimney was first introduced by Zandian and Ashjaee in 2013 to increase the efficiency of the solar updraft towers. This hybrid cooling-tower-solar-chimney system was shown to be able to produce an over ten times increase in output power compared to the conventional solar chimney power plants like Manzanares, Ciudad Real, with similar geometrical dimensions. In addition, it was shown that with an increase in chimney diameter, the power generation can reach to MW-graded power output without the necessity of building huge individual solar chimney panels. The results showed a maximum of 3 MW power output from the HCTSC system which resulted in 0.37% increase in the thermal efficiency of a typical 250 MW fossil fuel power plant, with a chimney diameter of only. The new hybrid design made the solar updraft tower feasible again, and proved it to be economical in saving lots of construction cost and time. This concept also recaptures the heat of radiators that are thrown out into the atmosphere without efficient utilization, and prevents generation of excessive greenhouse gasses.
The performance of an updraft tower may be degraded by factors such as atmospheric winds, by drag induced by the bracings used for supporting the chimney, and by reflection off the top of the greenhouse canopy.

Related ideas and adaptations

Updraft

A solar updraft power station would require a large initial capital outlay, but would have relatively low operating cost.
Capital outlays would be roughly the same as next-generation nuclear plants such as the AP-1000 at roughly $5 per Watt of capacity. As with other renewable power sources, towers have no need for fuel. Overall costs are largely determined by interest rates and years of operation, varying from 5 eurocent per kWh for 4% and 20 years to 15 eurocent per kWh for 12% and 40 years.
Estimates of total costs range from 7 and 21 euro cents per kWh to 25–35 cents per kWh. The levelized cost of energy is approximately 3 Euro cents per KWh for a 100 MW wind or natural gas plant. No actual data are available for a utility scale power plant.