Safety stock


Safety stock is a term used by logisticians to describe a level of extra stock that is maintained to mitigate risk of stockouts caused by uncertainties in supply and demand. Adequate safety stock levels permit business operations to proceed according to their plans. Safety stock is held when uncertainty exists in demand, supply, or manufacturing yield, and serves as an insurance against stockouts.
Safety stock is an additional quantity of an item held in the inventory to reduce the risk that the item will be out of stock. It acts as a buffer stock in case sales are greater than planned and/or the supplier is unable to deliver the additional units at the expected time.
With a new product, safety stock can be used as a strategic tool until the company can judge how accurate its forecast is after the first few years, especially when it is used with a material requirements planning worksheet. The less accurate the forecast, the more safety stock is required to ensure a given level of service. With an MRP worksheet, a company can judge how much it must produce to meet its forecasted sales demand without relying on safety stock. However, a common strategy is to try to reduce the level of safety stock to help keep inventory costs low once the product demand becomes more predictable. That can be extremely important for companies with a smaller financial cushion or those trying to run on lean manufacturing, which is aimed towards eliminating waste throughout the production process.
The amount of safety stock that an organization chooses to keep on hand can dramatically affect its business. Too much safety stock can result in high holding costs of inventory. In addition, products that are stored for too long a time can spoil, expire, or break during the warehousing process. Too little safety stock can result in lost sales and, in the thus a higher rate of customer turnover. As a result, finding the right balance between too much and too little safety stock is essential.

Reasons for keeping safety stock

Safety stocks are mainly used in a "make-to-stock" manufacturing strategy, which is employed when the lead time of manufacturing is too long to satisfy the customer demand at the right cost/quality/waiting time.
The main goal of safety stocks is to absorb the variability of customer demand. Indeed, production planning is based on a forecast, which is different from the real demand. By absorbing these variations, safety stock improves the customer-service level.
Creating a safety stock will also prevent stockouts from other variations, like an upward trend in customer demand.
Safety stock is used as a buffer to protect organizations from stockouts caused by inaccurate planning or poor schedule adherence by suppliers. As such, its cost is often seen as a drain on financial resources that results in reduction initiatives. In addition, time-sensitive goods such as food, drink, and other perishable items could spoil and go to waste if held as safety stock for too long. Various methods exist to reduce safety stock; these include better use of technology, increased collaboration with suppliers, and more accurate forecasting. In a lean supply environment, lead times are reduced, which can help minimize safety stock levels, thus reducing the likelihood and impact of stockouts.
Due to the cost of safety stock, many organizations opt for a service level-led safety stock calculation; for example, a 95% service level could result in stockouts, but is at a level that is acceptable to the company. The lower the service level, the lower the requirement for safety stock.
An enterprise resource planning system can also help an organization reduce its level of safety stock. Most ERP systems provide a type of production planning module. An ERP module such as this can help a company develop highly accurate and dynamic sales forecasts and sales and operations plans. By creating more accurate and dynamic forecasts, a company reduces its chance of producing insufficient inventory for a given period, thus should be able to reduce the amount of safety stock required. In addition, ERP systems use established formulas to help calculate appropriate levels of safety stock based on the previously developed production plans. While an ERP system aids an organization in estimating a reasonable amount of safety stock, the ERP module must be set up to plan requirements effectively.

Inventory policy

The size of the safety stock depends on the type of inventory policy in effect. An inventory node is supplied from a "source" which fulfills orders for the considered product after a certain replenishment lead time. In a periodic inventory policy, the inventory level is checked periodically and an order is placed at that time as to meet the expected demand until the next order. In this case, the safety stock is calculated considering the demand and supply variability risks during this period plus the replenishment lead time. If the inventory policy is continuous policy the inventory level is continuously monitored and orders are placed with freedom of time. In this case, safety stock is calculated considering the risk of only the replenishment lead time. If applied correctly, continuous inventory policies can lead to smaller safety stock whilst ensuring higher service levels, in line with lean processes and more efficient overall business management. However, continuous inventory policies are much harder to implement, so most of the organisations using traditional planning processes and tools opt for periodic inventory policy.

Methods for calculating safety stocks

Reorder point method with demand and lead time uncertainty for type I service

A commonly used approach calculates the safety stock based on the following factors:
Assuming that demand during successive unit time periods are independent and identically distributed random variables drawn from a normal distribution, the safety stock can be calculated as:
where,
The reorder point can then be calculated as:
The first term in the ROP formula is the average demand during the lead time. The second term is the safety stock. If the lead time is deterministic, i.e., then the ROP formula is simplified as.

Issues with this approach

No universal formula exists for safety stock, and application of the one above can cause serious damage.
It makes several implicit assumptions:
Another popular approach described by Nahmias uses the standardized unit loss integral L, given by:
Where is cumulative distribution function for the standard normal. Let β be the proportion of demands met from stock, Q the order quantity and σ the standard deviation of demand, then the following relationship holds:
In this case, the safety stock is given by:
and the expected number of units out of stock during an order cycle is given by σL.