Plate theory


In continuum mechanics, plate theories are mathematical descriptions of the mechanics of flat plates that draws on the theory of beams. Plates are defined as plane structural elements with a small thickness compared to the planar dimensions. The typical thickness to width ratio of a plate structure is less than 0.1. A plate theory takes advantage of this disparity in length scale to reduce the full three-dimensional solid mechanics problem to a two-dimensional problem. The aim of plate theory is to calculate the deformation and stresses in a plate subjected to loads.
Of the numerous plate theories that have been developed since the late 19th century, two are widely accepted and used in engineering. These are
The Kirchhoff–Love theory is an extension of Euler–Bernoulli beam theory to thin plates. The theory was developed in 1888 by Love using assumptions proposed by Kirchhoff. It is assumed that a mid-surface plane can be used to represent the three-dimensional plate in two-dimensional form.
The following kinematic assumptions that are made in this theory:
The Kirchhoff hypothesis implies that the displacement field has the form
where and are the Cartesian coordinates on the mid-surface of the undeformed plate, is the coordinate for the thickness direction, are the in-plane displacements of the mid-surface, and is the displacement of the mid-surface in the direction.
If are the angles of rotation of the normal to the mid-surface, then in the Kirchhoff–Love theory

Strain-displacement relations

For the situation where the strains in the plate are infinitesimal and the rotations of the mid-surface normals are less than 10° the strains-displacement relations are
Therefore, the only non-zero strains are in the in-plane directions.
If the rotations of the normals to the mid-surface are in the range of 10° to 15°, the strain-displacement relations can be approximated using the von Kármán strains. Then the kinematic assumptions of Kirchhoff-Love theory lead to the following strain-displacement relations
This theory is nonlinear because of the quadratic terms in the strain-displacement relations.

Equilibrium equations

The equilibrium equations for the plate can be derived from the principle of virtual work. For the situation where the strains and rotations of the plate are small, the equilibrium equations for an unloaded plate are given by
where the stress resultants and stress moment resultants are defined as
and the thickness of the plate is. The quantities are the stresses.
If the plate is loaded by an external distributed load that is normal to the mid-surface and directed in the positive direction, the principle of virtual work then leads to the equilibrium equations
For moderate rotations, the strain-displacement relations take the von Karman form and the equilibrium equations can be expressed as

Boundary conditions

The boundary conditions that are needed to solve the equilibrium equations of plate theory can be obtained from the boundary terms in the principle of virtual work.
For small strains and small rotations, the boundary conditions are
Note that the quantity is an effective shear force.

Stress–strain relations

The stress–strain relations for a linear elastic Kirchhoff plate are given by
Since and do not appear in the equilibrium equations it is implicitly assumed that these quantities do not have any effect on the momentum balance and are neglected.
It is more convenient to work with the stress and moment resultants that enter the equilibrium equations. These are related to the displacements by
and
The extensional stiffnesses are the quantities
The bending stiffnesses are the quantities

Isotropic and homogeneous Kirchhoff plate

For an isotropic and homogeneous plate, the stress–strain relations are
The moments corresponding to these stresses are

Pure bending

The displacements and are zero under pure bending conditions. For an isotropic, homogeneous plate under pure bending the governing equation is
In index notation,
In direct tensor notation, the governing equation is

Transverse loading

For a transversely loaded plate without axial deformations, the governing equation has the form
where
In index notation,
and in direct notation
In cylindrical coordinates, the governing equation is

Orthotropic and homogeneous Kirchhoff plate

For an orthotropic plate
Therefore,
and

Transverse loading

The governing equation of an orthotropic Kirchhoff plate loaded transversely by a distributed load per unit area is
where

Dynamics of thin Kirchhoff plates

The dynamic theory of plates determines the propagation of waves in the plates, and the study of standing waves and vibration modes.

Governing equations

The governing equations for the dynamics of a Kirchhoff–Love plate are
where, for a plate with density,
and
The figures below show some vibrational modes of a circular plate.

Isotropic plates

The governing equations simplify considerably for isotropic and homogeneous plates for which the in-plane deformations can be neglected and have the form
where is the bending stiffness of the plate. For a uniform plate of thickness,
In direct notation

Uflyand-Mindlin theory for thick plates

In the theory of thick plates, or theory of Yakov S. Uflyand, Raymond Mindlin and Eric Reissner, the normal to the mid-surface remains straight but not necessarily perpendicular to the mid-surface. If and designate the angles which the mid-surface makes with the axis then
Then the Mindlin–Reissner hypothesis implies that

Strain-displacement relations

Depending on the amount of rotation of the plate normals two different approximations for the strains can be derived from the basic kinematic assumptions.
For small strains and small rotations the strain-displacement relations for Mindlin–Reissner plates are
The shear strain, and hence the shear stress, across the thickness of the plate is not neglected in this theory. However, the shear strain is constant across the thickness of the plate. This cannot be accurate since the shear stress is known to be parabolic even for simple plate geometries. To account for the inaccuracy in the shear strain, a shear correction factor is applied so that the correct amount of internal energy is predicted by the theory. Then

Equilibrium equations

The equilibrium equations have slightly different forms depending on the amount of bending expected in the plate. For the situation where the strains and rotations of the plate are small the equilibrium equations for a Mindlin–Reissner plate are
The resultant shear forces in the above equations are defined as

Boundary conditions

The boundary conditions are indicated by the boundary terms in the principle of virtual work.
If the only external force is a vertical force on the top surface of the plate, the boundary conditions are

Constitutive relations

The stress–strain relations for a linear elastic Mindlin–Reissner plate are given by
Since does not appear in the equilibrium equations it is implicitly assumed that it do not have any effect on the momentum balance and is neglected. This assumption is also called the plane stress assumption. The remaining stress–strain relations for an orthotropic material, in matrix form, can be written as
Then,
and
For the shear terms
The extensional stiffnesses are the quantities
The bending stiffnesses are the quantities

Isotropic and homogeneous Uflyand-Mindlin plates

For uniformly thick, homogeneous, and isotropic plates, the stress–strain relations in the plane of the plate are
where is the Young's modulus, is the Poisson's ratio, and are the in-plane strains. The through-the-thickness shear stresses and strains are related by
where is the shear modulus.

Constitutive relations

The relations between the stress resultants and the generalized displacements for an isotropic Mindlin–Reissner plate are:
and
The bending rigidity is defined as the quantity
For a plate of thickness, the bending rigidity has the form
where

Governing equations

If we ignore the in-plane extension of the plate, the governing equations are
In terms of the generalized deformations, the three governing equations are
The boundary conditions along the edges of a rectangular plate are

Reissner–Stein static theory for isotropic cantilever plates

In general, exact solutions for cantilever plates using plate theory are quite involved and few exact solutions can be found in the literature. Reissner and Stein provide a simplified theory for cantilever plates that is an improvement over older theories such as Saint-Venant plate theory.
The Reissner-Stein theory assumes a transverse displacement field of the form
The governing equations for the plate then reduce to two coupled ordinary differential equations:
where
At, since the beam is clamped, the boundary conditions are
The boundary conditions at are
where
where is the transverse displacement, is the length, is the width, is the Poisson's
ratio, is the Young's modulus, and
The potential energy of transverse loads is
The potential energy of in-plane loads is
The potential energy of tip forces , and bending moments and
is
A balance of energy requires that the total energy is
With the Reissener–Stein assumption for the displacement, we have
and
Taking the first variation of with respect to and
setting it to zero gives us the Euler equations
and
where
Since the beam is clamped at, we have
The boundary conditions at can be found by integration by parts:
where