An overhead valveengine, sometimes called a pushrod engine, is a piston engine whose valves are located in the cylinder head above the combustion chamber. This contrasts with earlier flathead engines, where the valves were located below the combustion chamber in the engine block. The camshaft in an OHV engine is located in the engine block. The motion of the camshaft is transferred using pushrods and rocker arms to operate the valves at the top of the engine. Technically, an overhead camshaft engine also has overhead valves; however, to avoid confusion, OHC engines are not usually described as overhead valve engines. Some early "intake over exhaust" engines used a hybrid design combining elements of both side-valves and overhead valves.
History
Predecessors
The first internal combustion engines were based on steam engines and therefore used slide valves. This was the case for the first Otto engine, which was first successfully run in 1876. As internal combustion engines began to develop separately to steam engines, poppet valves became increasingly common, with most engines until the 1950s using a side-valve design. Beginning with the 1885 Daimler Reitwagen, several cars and motorcycles used inlet valve located in the cylinder head, however these valves were vacuum-actuated rather than driven by a camshaft as per typical OHV engines. The exhaust valve were driven by a camshaft, but were located in the engine block as per side-valve engines. The 1894 Diesel prototype engine used overhead poppet valves actuated by a camshaft, pushrods and rocker arms, therefore becoming one of the first OHV engines. In 1896, U.S. patent 563,140 was taken out by William F. Davis for an OHV engine with liquid coolant used to cool the cylinder head. but no working model was built.
Production OHV engines
In 1898, bicycle manufacturer Walter Lorenzo Marr in the United States built a prototype motorised tricycle powered by a single-cylinder OHV engine. Marr was hired by Buick from 1899–1902, where the overhead valve engine design was further refined. This engine employed pushrod-actuated rocker arms, which in turn opened valves parallel to the pistons. Marr returned to Buick in 1904, the same year that Buick received a patent for an overhead valve engine design. In 1904, the world's first production OHV engine was released in the Buick Model B. The engine was a flat-twin design with two valves per cylinder. The engine was very successful for Buick, with the company selling 750 such cars in 1905. Several other manufacturers began to produce OHV engines, such as the 1906–1912 Wright BrothersVertical 4-Cylinder Engine. However, side-valve engines remained commonplace until the late 1940s, when they began to be phased out for OHV engines.
Replacement by OHC engines
The first overhead camshaft engine dates back to 1902, however use of this design was mostly limited to high performance cars for many decades. OHC engines slowly became more common from the 1950s to the 1990s, and by the start of the 21st century, the majority of automotive engines used an OHC design. At the 1994 Indianapolis 500 motor race, Team Penske entered a car powered by the custom built Mercedes-Benz 500I OHV engine. Due to a loophole in the rules, the OHV engine was allowed to use a larger displacement and higher boost pressure, significantly increasing its power output compared to the OHC engines used by other teams. Team Penske qualified in pole position and won the race by a large margin. In the early 21st century, several OHV V8 engines from General Motors and Chrysler used variable displacement to reduce fuel consumption and exhaust emissions. In 2008, the first production OHV engine to use variable valve timing was introduced in the Dodge Viper.
Design
OHV engines have several advantages compared OHC engines:
Smaller overall packaging: The cam-in-block design of an OHV engine results in a smaller overall size, compared with an equivalent OHC engine.
Use of the same cylinder head casting for both cylinder banks: An OHC engine requires the cylinder heads to be mirror images of each other, due to the camshaft drive system at the front of each cylinder bank. An OHV engine can use the same cylinder head casting for both banks, by simply flipping it around for the second bank.
Simpler camshaft drive system: OHV engines have a less complex drive system for the camshaft when compared with OHC engines. Most OHC engines drive the camshaft or camshafts using a timing belt, a chain, or multiple chains. These systems require the use of tensioners, which add complexity. In contrast, an OHV engine has the camshaft positioned close to the crankshaft, which may be driven by a much shorter chain or even direct gear connection. However, this is somewhat negated by a more complex valvetrain requiring pushrods.
Simpler lubrication system: The lubrication requirements for OHV cylinder heads are much less, due to the lack of a camshaft and related bearings to lubricate. OHV heads only need lubrication for the rocker arms at the pushrod end, trunnion, and rocker tip. This lubrication to is typically provided through the pushrods themselves rather than a dedicated lubrication system in the head. The reduced lubrication requirements can also mean that a smaller, lower-capacity oil pump is used.
Compared with OHC engines, OHV engines have the following disadvantages:
Limited engine speeds: Although OHV engines have simpler drive systems for the camshaft, there are a greater number of moving parts in the valvetrain. Inertia from these valvetrain parts makes OHV engines more susceptible to valve float at high engine speeds.
Constraints on valve quantity and location: OHC engines often have four valves per cylinder, whereas it is rare for an OHV engine to have more than two valves per cylinder. In OHV engines, the size and shape of the intake ports as well as the position of the valves are limited by the pushrods and the need to accommodate them in the head casting.
