The Moynet 360 Jupiter was a small executive transport built in France in the 1960s. It had an unusual twin-push-pull, single-fuselage configuration. Two prototypes were produced, the second with more power and seating, but no sales resulted.
Design and development
Some civil propeller driven aircraft that have used one or more pairs of engines in push-pull configuration have been flying boats, with engines mounted above the wing and clear of spray. Others have had a pair of engines, one at either end of a pod fuselage with a tail unit mounted on a pair of booms, for example the Cessna Skymaster, the Adam A500 or the Rutan Voyager. The Moynet 360 Jupiter was an example of a push-pull aircraft of a less common configuration, where a single conventional fuselage has an engine at either end; the Dornier Do 335 fighter used the same arrangement. For light civil aircraft, the aim was to combine the performance of a conventional twin-engined aircraft with the ease of handling of a single-engined one. The Jupiter was an executive transport with between four and seven seats, depending on engine power. It was designed by André Moynet, a member of the National Assembly of France and a former government minister, while also a test-pilot, and built by S.S. Engins Matra, the first prototype flying on 17 December 1963 with the designer and Lucien Tieles at the controls. Its wing had a straight trailing edge, but the centre section had strong taper on the leading edge which continued more weakly outboard. It was of two spar, stressed skin construction, carrying mass balanced ailerons and slotted flaps. The main undercarriage legs, placed at the end of the centre section each carried a single wheel and retracted inwards electrically. A retractable nosewheel completed the landing gear. One horizontally opposedLycoming engine was conventionally placed in the nose. Behind it was a standard cabin, though the front seats were further ahead of the leading edge than usual because of the rearward shift of the centre of gravity caused by the rear engine. There were three large windows on each side. For the same reason the rear fuselage was quite short, and it lacked the normal taper, giving it a boxy look, so that the second, pusher Lycoming could be mounted in the extreme tail. This was cooled by air from rectangular intakes on the upper sides of the rear fuselage. The straight edged, tapered tailplane was mounted on the fuselage top above the engine, with small endplate fins carrying balanced rudders. These fins extended above and below the tailplane, with arrow shaped leading edges and straight, swept trailing edges. There was also a long, shallow strake over the rear fuselage. Seen from below, the long span of the tailplane was striking, about 44% of that of the wings; the elevators filled most of the outer part of its trailing edge, avoiding the propeller airstream. Only two Jupiters were built. The first, designated 360-4 and initially registered as F-WLKE had two 200 hp Lycoming IO-360-A1A engines driving two-bladed propellers and was configured as a 4-5 seater. The second prototype was of a more powerful and slightly larger variant designated the model 360-6; it first flew on 25 May 1965. This model had a choice of engines, either 290 hp Lycoming IO-540six cylinder engines driving constant speed, three-bladed propellers, or 310 hp Lycoming TIO-541 engines. The span was increased by 0.37 m and length by 0.64 m. The increased length allowed seats for 6-7, with two rows of two single seats and a bench seat at the rear that could accommodate 2 or 3. The cabin was sound-proofed and air conditioned and could be pressurised. Access was via a forward starboard side door. There was baggage space behind the cabin with its own external door. The sole 360-6 was registered as F-WLKY. The intention was for Sud-Aviation to produce the 360-6 Jupiter as the Sud-Aviation M 360-6 Jupiter. An order was obtained from the French government for some 360-6 pre-production aircraft, but this seems to have been cancelled. Despite sales campaigns in Europe and the United States no further orders resulted. The first prototype is now in the reserve collection of the Musée de l'Air et de l'Espace, Le Bourget Airport, Paris museum and the second in the Musée Regional de l'Air, Angers - Loire Airport, France. At le Bourget, the 360-4 bears the normal French registration F-BLKE rather than the French prototype style F-WLKE.
