M1911 pistol


The M1911, also known as the Colt Government or "Government", is a single-action, semi-automatic, magazine-fed, recoil-operated pistol chambered for the.45 ACP cartridge. It served as the standard-issue sidearm for the United States Armed Forces from 1911 to 1986. It was widely used in World War I, World War II, the Korean War, and the Vietnam War. The pistol's formal designation as of 1940 was Automatic Pistol, Caliber.45, M1911 for the original model of 1911 or Automatic Pistol, Caliber.45, M1911A1 for the M1911A1, adopted in 1924. The designation changed to Pistol, Caliber.45, Automatic, M1911A1 in the Vietnam War era.
The U.S. procured around 2.7 million M1911 and M1911A1 pistols in military contracts during its service life. The M1911 was replaced by the 9 mm Beretta M9 pistol as the standard U.S. sidearm in October 1986, but due to its popularity among users, it has not been completely phased out. Modernized derivative variants of the M1911 are still in use by some units of the U.S. Army Special Forces and the U.S. Navy.
Designed by John Browning, the M1911 is the best-known of his designs to use the short recoil principle in its basic design. The pistol was widely copied, and this operating system rose to become the preeminent type of the 20th century and of nearly all modern centerfire pistols. It is popular with civilian shooters in competitive events such as USPSA, IDPA, International Practical Shooting Confederation, and bullseye shooting. Compact variants are popular civilian concealed carry weapons in the U.S. because of the design's relatively slim width and the stopping power of the.45 ACP cartridge.

History

Early history and adaptations

The M1911 pistol originated in the late 1890s as the result of a search for a suitable self-loading pistol to replace the variety of revolvers then in service. The United States was adopting new firearms at a phenomenal rate; several new pistols and two all-new service rifles, as well as a series of revolvers by Colt and Smith & Wesson for the Army and Navy, were adopted just in that decade. The next decade would see a similar pace, including the adoption of several more revolvers and an intensive search for a self-loading pistol that would culminate in official adoption of the M1911 after the turn of the decade.
Hiram S. Maxim had designed a self-loading rifle in the 1880s, but was preoccupied with machine guns. Nevertheless, the application of his principle of using cartridge energy to reload led to several self-loading pistols in 1896. The designs caught the attention of various militaries, each of which began programs to find a suitable one for their forces. In the U.S., such a program would lead to a formal test at the turn of the 20th century.

During the end of 1899 and start of 1900, a test of self-loading pistols, including entries from Mauser, Mannlicher, and Colt, was conducted.
This led to a purchase of 1,000 DWM Luger pistols, chambered in 7.65mm Luger, a bottlenecked cartridge. During field trials, these ran into some problems, especially with stopping power. Other governments had made similar complaints. Consequently, DWM produced an enlarged version of the round, the 9×19mm Parabellum, a necked-up version of the 7.65 mm round. Fifty of these were tested as well by the U.S. Army in 1903.
American units fighting guerrillas in the Moro Rebellion in Sulu during the Philippine–American War using the then-standard Colt M1892 revolver,.38 Long Colt, found it to be unsuitable for the rigors of jungle warfare, particularly in terms of stopping power, as the Moros had high battle morale and often used drugs to inhibit the sensation of pain. The U.S. Army briefly reverted to using the M1873 single-action revolver in.45 Colt caliber, which had been standard during the late 19th century; the heavier bullet was found to be more effective against charging tribesmen. The problems prompted the Chief of Ordnance, General William Crozier, to authorize further testing for a new service pistol.
Following the 1904 Thompson-LaGarde pistol round effectiveness tests, Colonel John T. Thompson stated that the new pistol "should not be of less than.45 caliber" and would preferably be semi-automatic in operation. This led to the 1906 trials of pistols from six firearms manufacturing companies.
Of the six designs submitted, three were eliminated early on, leaving only the Savage, Colt, and DWM designs chambered in the new.45 ACP cartridge. These three still had issues that needed correction, but only Colt and Savage resubmitted their designs. There is some debate over the reasons for DWM's withdrawal—some say they felt there was bias and that the DWM design was being used primarily as a "whipping boy" for the Savage and Colt pistols, though this does not fit well with the earlier 1900 purchase of the DWM design over the Colt and Steyr entries. In any case, a series of field tests from 1907 to 1911 were held to decide between the Savage and Colt designs. Both designs were improved between each round of testing, leading up to the final test before adoption.
Among the areas of success for the Colt was a test at the end of 1910 attended by its designer, John Browning. Six thousand rounds were fired from a single pistol over the course of two days. When the gun began to grow hot, it was simply immersed in water to cool it. The Colt gun passed with no reported malfunctions, while the Savage designs had 37.

Service history

Following its success in trials, the Colt pistol was formally adopted by the Army on March 29, 1911, when it was designated Model of 1911, later changed to Model 1911, in 1917, and then M1911, in the mid-1920s. The Director of Civilian Marksmanship began manufacture of M1911 pistols for members of the National Rifle Association in August 1912. Approximately 100 pistols stamped "N.R.A." below the serial number were manufactured at Springfield Armory and by Colt. The M1911 was formally adopted by the U.S. Navy and Marine Corps in 1913. The.45 ACP "Model of 1911 U.S. Army" was used by both US Army Cavalry Troops and Infantry Soldiers during the United States' Punitive Expedition into Mexico against Pancho Villa in 1916.

World War I

By the beginning of 1917, a total of 68,533 M1911 pistols had been delivered to U.S. armed forces by Colt's Patent Firearms Manufacturing Company and the U.S. government's Springfield Armory. However, the need to greatly expand U.S. military forces and the resultant surge in demand for the firearm in World War I saw the expansion of manufacture to other contractors besides Colt and Springfield Armory, including Remington-UMC and North American Arms Co. of Quebec. Several other manufacturers were awarded contracts to produce the M1911, including the National Cash Register Company, the Savage Arms Company, the Caron Brothers Manufacturing of Montreal, the Burroughs Adding Machine Co., Winchester Repeating Arms Company, and the Lanston Monotype Company, but the signing of the Armistice resulted in the cancellation of the contracts before any pistols had been produced.

Interwar changes

Battlefield experience in World War I led to some more small external changes, completed in 1924. The new version received a modified type classification, M1911A1, in 1926 with a stipulation that M1911A1s should have serial numbers higher than 700,000 with lower serial numbers designated M1911. The M1911A1 changes to the original design consisted of a shorter trigger, cutouts in the frame behind the trigger, an arched mainspring housing, a longer grip safety spur, a wider front sight, a shortened hammer spur, and simplified grip checkering. These changes were subtle and largely intended to make the pistol easier to shoot for those with smaller hands. Many persons unfamiliar with the design are often unable to tell the difference between the two versions at a glance. No significant internal changes were made, and parts remained interchangeable between the M1911 and the M1911A1.
Working for the U.S. Ordnance Office, David Marshall Williams developed a.22 training version of the M1911 using a floating chamber to give the.22 long rifle rimfire recoil similar to the.45 version. As the Colt Service Ace, this was available both as a pistol and as a conversion kit for.45 M1911 pistols.
Before World War II, 500 M1911s were produced under license by the Norwegian arms factory Kongsberg Vaapenfabrikk, as Automatisk Pistol Model 1912. Then, production moved to a modified version designated Pistol Model 1914 and unofficially known as "Kongsberg Colt". The Pistol M/1914 is noted for its unusual extended slide stop which was specified by Norwegian ordnance authorities. 22,000 were produced between 1914 and 1940 but production continued after the German occupation of Norway in 1940 and 10,000 were produced for the German armed forces as Pistole 657 .
Between 1927 and 1966, 102,000 M1911 pistols were produced as Sistema Colt Modelo 1927 in Argentina, first by the Dirección General de Fabricaciones Militares. A similar gun, the Ballester–Molina, was also designed and produced.
The M1911 and M1911A1 pistols were also ordered from Colt or produced domestically in modified form by several other nations, including Brazil, Mexico, and Spain.

World War II

and the years leading up to it created a great demand. During the war, about 1.9 million units were procured by the U.S. Government for all forces, production being undertaken by several manufacturers, including Remington Rand, Colt, Ithaca Gun Company, Union Switch & Signal, and Singer. New M1911A1 pistols were given a parkerized metal finish instead of bluing, and the wood grip panels were replaced with panels made of brown plastic. The M1911A1 was a favored small arm of both US and allied military personnel during the war, in particular, the pistol was prized by some British commando units and Britain's highly covert Special Operations Executive, as well as South African Commonwealth forces.
So many 1911A1 pistols were produced during the war that the government canceled all postwar contracts for new production, instead choosing to rebuild existing pistols with new parts, which were then refinished and tested for functioning. From the mid-1920s to the mid-1950s thousands of 1911s and 1911A1s were refurbished at U.S. Arsenals and Service depots. These arsenal rebuilds consisted of anything from minor inspections to major overhauls of pistols returned from service use. Pistols that were refurbished at government arsenals will usually be marked on the frame/receiver with the arsenal's initials, such as RIA or SA.
Among collectors today, the Singer-produced pistols in particular are highly prized, commanding high prices even in poor condition.

General Officer's Model

From 1943 to 1945 a fine-grade russet-leather M1916 pistol belt set was issued to some generals in the US Army. It was composed of a leather belt, leather enclosed flap-holster with braided leather tie-down leg strap, leather two-pocket magazine pouch, and a rope neck lanyard. The metal buckle and fittings were in gilded brass. The buckle had the seal of the U.S. on the center piece and a laurel wreath on the circular piece. The pistol was a standard-issue M1911A1 that came with a cleaning kit and three magazines.
From 1972 to 1981 a modified M1911A1 called the RIA M15 General Officer's Model was issued to General Officers in the US Army and US Air Force. From 1982 to 1986 the regular M1911A1 was issued. Both came with a black leather belt, open holster with retaining strap, and a two-pocket magazine pouch. The metal buckle and fittings were similar to the M1916 General Officer's Model except it came in gold metal for the Army and in silver metal for the Air Force. The M15 and M1911A1 were replaced with the M9 pistol in 1986.

Post World War II usage

After World War II, the M1911 continued to be a mainstay of the U.S. Armed Forces in the Korean War and the Vietnam War. It was used during Desert Storm in specialized U.S. Army units and U.S. Navy Mobile Construction Battalions, and has seen service in both Operation Iraqi Freedom and Operation Enduring Freedom, with U.S. Army Special Forces Groups and Marine Corps Force Reconnaissance Companies.
However, by the late 1970s, the M1911A1 was acknowledged to be showing its age. Under political pressure from Congress to standardize on a single modern pistol design, the U.S. Air Force ran a Joint Service Small Arms Program to select a new semi-automatic pistol using the NATO-standard 9 mm Parabellum pistol cartridge. After trials, the Beretta 92S-1 was chosen. The Army contested this result and subsequently ran its own competition in 1981, the XM9 trials, eventually leading to the official adoption of the Beretta 92F on January 14, 1985. By the late 1980s production was ramping up despite a controversial XM9 retrial and a separate XM10 reconfirmation that was boycotted by some entrants of the original trials, cracks in the frames of some pre-M9 Beretta-produced pistols, and despite a problem with slide separation using higher-than-specified-pressure rounds that resulted in injuries to some U.S. Navy special operations operatives. This last issue resulted in an updated model that includes additional protection for the user, the 92FS, and updates to the ammunition used. During the Gulf War of 1990 to 1991, M1911A1s were deployed with reserve component U.S. Army units sent to participate in Operation Desert Storm.
By the early 1990s, most M1911A1s had been replaced by the Beretta M9, though a limited number remain in use by special units. The U.S. Marine Corps in particular were noted for continuing the use of M1911 pistols for selected personnel in MEU and reconnaissance units For its part, the United States Special Operations Command issued a requirement for a.45 ACP pistol in the Offensive Handgun Weapon System trials. This resulted in the Heckler & Koch OHWS becoming the MK23 Mod 0 Offensive Handgun Weapon System, beating the Colt OHWS, a much-modified M1911. Dissatisfaction with the stopping power of the 9 mm Parabellum cartridge used in the Beretta M9 has actually promoted re-adoption of pistols based on the.45 ACP cartridge such as the M1911 design, along with other pistols, among USSOCOM units in recent years, though the M9 has been predominant both within SOCOM and in the U.S. military in general. Both U.S. Army Special Forces Units and SFOD-D continue to use modernized M1911s.

MEU(SOC) pistol

s formerly issued M1911s to Force Recon units. Hand-selected Colt M1911A1 frames were gutted, deburred, and prepared for additional use by the USMC Precision Weapon Section at Marine Corps Base Quantico. They were then assembled with after-market grip safeties, ambidextrous thumb safeties, triggers, improved high-visibility sights, accurized barrels, grips, and improved Wilson magazines. These hand-made pistols were tuned to specifications and preferences of end users.
In the late 1980s, the Marines laid out a series of specifications and improvements to make Browning's design ready for 21st-century combat, many of which have been included in MEU pistol designs, but design and supply time was limited. Discovering that the Los Angeles Police Department was pleased with their special Kimber M1911 pistols, a single source request was issued to Kimber for just such a pistol despite the imminent release of their TLE/RLII models. Kimber shortly began producing a limited number of what would be later termed the Interim Close Quarters Battle pistol. Maintaining the simple recoil assembly, 5-inch barrel, and internal extractor, the ICQB is not much different from Browning's original design.
In July 2012, the U.S. Marines placed a $22.5 million order with Colt for 12,000 M1911 pistols for MEU forces. The new 1911 was designated M45A1 or "Close Quarters Battle Pistol" CQBP. The M45A1 features a dual recoil spring assembly, Picatinny rails and is cerakoted tan in color.
M45A1 pistols continue to see usage today with USMC Force Recon Battalions, in addition to other specialized USMC units.

Current users in the U.S.

Many military and law enforcement organizations in the U.S. and other countries continue to use M1911A1 pistols including Los Angeles Police Department SWAT and S.I.S., the FBI Hostage Rescue Team, FBI regional SWAT teams, and 1st Special Forces Operational Detachment—Delta.
.
The M1911A1 is popular among the general public in the U.S. for practical and recreational purposes. The pistol is commonly used for concealed carry thanks in part to a single-stack magazine, personal defense, target shooting, and competition as well as collections. Numerous aftermarket accessories allow users to customize the pistol to their liking. There are a growing number of manufacturers of M1911-type pistols and the model continues to be quite popular for its reliability, simplicity, and patriotic appeal. Various tactical, target and compact models are available. Price ranges from a low end of around $400 for basic pistols imported from the Philippines or Turkey to more than $4,000 for the best competition or tactical versions.
Due to an increased demand for M1911 pistols among Army Special Operations units, who are known to field a variety of M1911 pistols, the U.S. Army Marksmanship Unit began looking to develop a new generation of M1911s and launched the M1911-A2 project in late 2004. The goal was to produce a minimum of seven variants with various sights, internal and external extractors, flat and arched mainspring housings, integral and add-on magazine wells, a variety of finishes and other options, with the idea of providing the end-user a selection from which to select the features that best fit their missions. The AMU performed a well-received demonstration of the first group of pistols to the Marine Corps at Quantico and various Special Operations units at Ft. Bragg and other locations. The project provided a feasibility study with insight into future projects. Models were loaned to various Special Operations units, the results of which are classified. An RFP was issued for a Joint Combat Pistol but it was ultimately canceled. Currently units are experimenting with an M1911 pistol in.40 which will incorporate lessons learned from the A2 project. Ultimately, the M1911A2 project provided a testbed for improving existing M1911s. An improved M1911 variant becoming available in the future is a possibility.
The Springfield Custom Professional Model 1911A1 pistol is produced under contract by Springfield Armory for the FBI regional SWAT teams and the Hostage Rescue Team. This pistol is made in batches on a regular basis by the Springfield Custom Shop, and a few examples from most runs are made available for sale to the general public at a selling price of approximately US$2,700 each.

International users

Since its inception, the M1911 has lent itself to easy customization. Replacement sights, grips, and other aftermarket accessories are the most commonly offered parts. Since the 1950s and the rise of competitive pistol shooting, many companies have been offering the M1911 as a base model for major customization. These modifications can range from changing the external finish, checkering the frame, and hand fitting custom hammers, triggers, and sears. Some modifications include installing compensators and the addition of accessories such as tactical lights and even scopes. A common modification of John Browning's design is to use a full-length guide rod that runs the full length of the recoil spring. This adds weight to the front of the pistol, but does not increase accuracy, and does make the pistol slightly more difficult to disassemble. Custom guns can cost over $5,000 and are built from scratch or on existing base models. The main companies offering custom M1911s are: Dan Wesson Firearms, Ed Brown, Les Baer, Nighthawk Custom, Springfield Custom Shop, STI International, and Wilson Combat. IPSC models are offered by both Strayer Voigt Inc and STI International.

Design

Browning's basic M1911 design has seen very little change throughout its production life. The basic principle of the pistol is recoil operation. As the expanding combustion gases force the bullet down the barrel, they give reverse momentum to the slide and barrel which are locked together during this portion of the firing cycle. After the bullet has left the barrel, the slide and barrel continue rearward a short distance.
At this point, a link pivots the rear of the barrel down, out of locking recesses in the slide, and the barrel is stopped by making contact with the lower barrel lugs against the frame. As the slide continues rearward, a claw extractor pulls the spent casing from the firing chamber and an ejector strikes the rear of the case, pivoting it out and away from the pistol through the ejection port. The slide stops its rearward motion then, and is propelled forward again by the recoil spring to strip a fresh cartridge from the magazine and feed it into the firing chamber. At the forward end of its travel, the slide locks into the barrel and is ready to fire again. However, if the fired round was the last round in the magazine, the slide will lock in the rearward position, which notifies the shooter to reload by ejecting the empty magazine and inserting a loaded magazine, and facilitates reloading the chamber, which is accomplished by either pulling the slide back slightly and releasing, or by pushing down on the slide stop, which releases the slide to move forward under spring pressure, strip a fresh cartridge from the magazine and feed it into the firing chamber.
There are no fasteners of any type in the 1911 design, excepting the grip screws. The main components of the gun are held in place by the force of the main spring. The pistol can be "field stripped" by partially retracting the slide, removing the slide stop, and subsequently removing the barrel bushing. Full disassembly of the pistol to its component parts can be accomplished using several manually removed components as tools to complete the disassembly.
The military mandated a grip safety and a manual safety. A grip safety, sear disconnect, slide stop, half cock position, and manual safety are on all standard M1911A1s. Several companies have developed a firing pin block safety. Colt's 80 series uses a trigger operated one and several other manufacturers, including Kimber and Smith & Wesson, use a Swartz firing-pin safety, which is operated by the grip safety. Language cautioning against pulling the trigger with the second finger was included in the initial M1911 manual, and later manuals up to the 1940s.
The same basic design has been offered commercially and has been used by other militaries. In addition to the.45 ACP, models chambered for.38 Super, 9×19mm Parabellum, 7.65mm Parabellum, 9mm Steyr,.400 Corbon, and other cartridges were offered. The M1911 was developed from earlier Colt semi-automatic designs, firing rounds such as.38 ACP. The design beat out many other contenders during the government's selection period, during the late 1890s and early 1900s, up to the pistol's adoption. The M1911 officially replaced a range of revolvers and pistols across branches of the U.S. armed forces, though a number of other designs have seen use in certain niches.
Despite being challenged by newer and lighter weight pistol designs in.45 caliber, such as the Glock 21, the SIG Sauer P220, the Springfield XD and the Heckler & Koch USP, the M1911 shows no signs of decreasing popularity and continues to be widely present in various competitive matches such as those of USPSA, IDPA, IPSC, and Bullseye.

Users

Current

On March 18, 2011, the U.S. state of Utah—as a way of honoring M1911 designer John Browning, who was born and raised in the state—adopted the Browning M1911 as the "official firearm of Utah".

Similar pistols