Kriss Vector


The Kriss Vector series are a family of weapons based upon the parent submachine gun design developed by the American company Kriss USA, formerly Transformational Defense Industries. They use an unconventional delayed blowback system combined with in-line design to reduce perceived recoil and muzzle climb.

History

In the spring of 2007, TDI announced their development of a new submachine gun. It was an experimental weapon under advanced stages of development at that time. The name Kriss comes from a Southeast Asian dagger with a flame-shaped blade.
The second generation prototype of the Vector, called the K10, was announced at 2011 SHOT Show. It is a slightly more compact version of the Vector that is based on the same Super V system. The main difference is a redesign of the lower receiver intended for easy caliber interchangeability; utilizing just a single takedown pin, users can change between 9x19mm,.40 S&W and.45 ACP by mounting different lower receivers. This also brought a redesign of the charging handle, which now travels diagonally, almost vertically, and can be mounted on either side of the weapon. Other notable differences were a new telescoping stock instead of a folding one, and a four-sided accessory rail tube around the barrel. The K10 was not displayed after SHOT Show 2013 and its status is unknown and likely has been canceled.
Kriss announced "Gen II" versions of the original Vector models in 2015. These feature a redesigned pistol grip, trigger, safety selector, and compatibility with a new 9x19mm lower. These appear to have replaced the K10 prototypes, though no features from the K10 were carried over.

Design

The Vector uses an articulated mechanism referred to as the "Kriss Super V," which allows the bolt and an inertia block to move downward into a recess behind the magazine well. The theory is that at the end of this travel, the energy is transmitted downward rather than rearward, thus reducing the felt recoil. When fired, the barrel axis is in line with the shoulder as in the M16 rifle, but also in line with the shooter's hand. This is intended to reduce muzzle climb when combined with the off-axis bolt travel, though it also greatly raises the sight line in comparison to the bore axis. The initial prototype model by TDI achieved a rate of fire of 1,500 rounds per minute, though this was brought down to around 1,200 rounds per minute on the production models.
The Vector is split into two major assemblies in a similar manner to the AR-15 rifle, secured together with four push pins. Due to the weapon's unusual layout, the lower contains the action, charging handle, magazine well and barrel, while the upper contains the ejection port, rail system, pistol grip and fire control components, as well as the stock for configurations that have one. This modular design allows for toolless caliber conversions by swapping out only the lower. The Vector's safety is ambidextrous while the ejection port, charging handle, bolt release catch and magazine release are not, and are only available in a right-handed configuration.
Calibers such as.22 LR,.40 S&W and 9×19mm Parabellum were mentioned when the gun was first released. The Gen II versions with multiple design changes including a new 9 mm variant were confirmed at SHOT Show 2015, though the.22LR version had yet to materialize and was thought to have been canceled up until SHOT Show 2020, when they announced its release. The original.45-caliber Vector was designed to accept standard Glock 21 pistol magazines. A special "MagEx 30" kit was available to convert a factory 13-round.45 ACP Glock magazine to an extended high-capacity version, though this is now marketed as a "25+" round kit. The newer 9×19mm Parabellum versions instead use standard Glock 17 magazines.

Variants

The Vector family has undergone two generations of modification. The Gen I version is the baseline model of the Vector family. It was later replaced by the improved Gen II version which features a redesigned pistol grip and trigger and has the swing angle of the safety lever reduced from 120 to 45 degrees. It also eliminates the opening above the barrel for the original weapon's optional Surefire weapon light, since these are no longer manufactured. In addition to the original Flat Black finish, optional factory Cerakote coatings now come in Olive Drab, Flat Dark Earth, Alpine, or Combat Gray.
The Vector SMG variant is only available for military and law enforcement use. It features a 5.5-inch barrel, a folding stock, flip-up Midwest Industries back-up iron sights , a full-length Picatinny rail for mounting various optics/scopes, and either two mode fire selector or a three mode fire selector. It is only sold as a complete weapon in.45 ACP and 9×19mm Parabellum, though due to the nature of the weapon the auto trigger pack is compatible with any Vector lower. The 9mm model uses Glock 17-compatible magazines and the.45-caliber model uses Glock 21 magazines.
Semi-automatic versions are produced and available for the US civilian market. There are three main configurations, the Vector CRB, Vector SBR and Vector SDP. In addition to 9×19mm Parabellum and.45 ACP, they can also be chambered in.40 S&W, 10mm Auto, or.357 SIG. A variant chambered for 9×21mm IMI that feeds from standard 9×19mm Glock 17 magazines is available for the Italian civilian market. The.22 LR variant feeds from a proprietary 10 round magazine, and functions using a traditional straight blowback operating system rather than the Super V delayed system. The Canadian civil market versions only come with the blocked 10-round magazines rather than the full capacity magazines. Like the Law Enforcement / Military SMG models, the civilian model Vectors can be converted to chamber and fire other calibers if the lower receiver groups are changed.
The "Enhanced" versions of the Gen II CRB and SBR are also available with collapsing M4-style stock adaptors instead of the standard folding stock and a rectangular barrel shroud for the CRB, though these accessories can also be purchased separately.

Derivatives

Kriss announced development of a semi-automatic pistol called the "KRISS KARD" in 2010, using the Super V system in a much smaller package to minimize recoil and muzzle rise in 9×19mm Parabellum and.45 ACP calibers. It does not have a blowback slide, instead it has a T-shaped cocking handle on the rear. As TDI, Kriss also announced a 12-gauge shotgun called the MVS and a.50 BMG heavy machine gun using a double Super V mechanism called the "Disraptor," but the Disraptor has not been mentioned since their name change, while the MVS was removed from the TDI website in late 2009.

Users