Ice resurfacer


An ice resurfacer is a vehicle or hand-pushed device used to clean and smooth the surface of a sheet of ice, usually in an ice rink. The first ice resurfacer was developed by American inventor and engineer Frank Zamboni in 1949 in the city of Paramount, California. As such, an ice resurfacer is often referred to as a "Zamboni" regardless of brand or manufacturer.

History

The first ice resurfacer was invented by Frank Zamboni, who was originally in the refrigeration business. Zamboni created a plant for making ice blocks that could be used in refrigeration applications. As the demand for ice blocks waned with the spread of compressor-based refrigeration, he looked for another way to capitalize on his expertise with ice production.
In 1939, Zamboni built the Iceland Skating Rink in Paramount, California. In order to resurface the skating rink, 3 or 4 workers had to scrape, wash, and squeegee the ice. A thin layer of water was then added for the fresh ice. This process was extremely time consuming, and Zamboni wanted to find a more efficient way to resurface the ice.
From 1942 to 1947, he worked to develop a vehicle that could cut down on resurfacing time. In 1947, he built a machine that would shave, wash and squeegee the ice. This machine was mounted on an army surplus Willys Jeep chassis. A blade was mounted on the machine, which would shave the ice; the ice would then receive a thin layer of water creating a smooth sheet of ice. The prototype had a tank that held the ice shavings, which were carried to the tank via a conveyor belt. Zamboni abandoned this model in late 1947 because of deficiencies with the blade and handling.
A new machine was developed using another army surplus vehicle chassis. This machine had four-wheel drive as well as all-wheel steering. By 1949, the Model A Zamboni Ice Resurfacer was developed. Further modification to the Model A included the addition of a wash water tank and a cover for the snow-holding tank. The all-wheel steering feature was reduced to only front-wheel steering because the machine constantly got wedged against the boards. The Zamboni ice-resurfacer was patented in 1953.
.
The Model B was the next ice resurfacer made by Zamboni. The Zamboni Model C was also built on the same frame, but more design changes were applied. The driver's position was raised for better visibility, and the capacity of the snow-holding tank was increased. From the late 1950s to 1964, there were minimal changes in how the ice-resurfacers were designed. The introduction of the HD series in 1964 saw a shift in the design of the Zamboni ice resurfacers. Instead of relying on a conveyor belt system to move the ice shavings into the snow-holding tank, a vertical screw conveyor system was installed, and a new hydraulic snow-dumping system was adopted. This design has been the industry standard since it was first adopted.
In 1967, an Elmira, Ontario-based welder named Andrew Schlupp founded the Resurfice Corporation and began producing competing models of resurfacers, including their popular Olympia line. In 1980 an Italian company, Engo Ice Arena Equipment, began producing ice resurfacers.

Technology

Ice resurfacers are generally composed of a snow container, hot water tanks, a wash water tank, the conditioner, and a board brush. The engine or motor of the vehicle is responsible both for propelling the resurfacer and also powering the hydraulics that control the various functions, such as lowering the conditioner or raising the snow dump.
Most of the actual resurfacing components are contained in a heavy device at the rear of the machine, known as the "conditioner". The conditioner is hydraulically lowered to the ice surface, its weight providing the friction necessary for a large, sharp blade to shave off the top layer of ice. A horizontal auger conveyor collects these ice shavings, or snow, and funnels them to a vertical auger at the center of the conditioner. The shavings are then carried upward and sprayed into a large snow container, which takes up most of the volume of the resurfacer.
The height of the blade can be adjusted by the driver, allowing deeper or shallower cuts. This is useful for keeping the ice sheet level, improving the quality of the cut, and preventing the snow container from overflowing.
Wash water can be used to further improve the quality of the ice by removing debris and snow from deep skate-blade cuts. Located directly in front of the blade, nozzles forcefully spray water into the ice surface, loosening deep debris. Runners on either side of the conditioner contain the spray, while a rubber squeegee at the rear of the conditioner allows a vacuum nozzle to pick up excess water. This water is then filtered through a screen and recirculated.
Finally, a layer of water is laid down to fill in the remaining grooves in the ice. The ice-making water is released through a sprinkler pipe at the rear of the conditioner, which wets the cloth towel that is dragged behind the resurfacer. The towel ensures a smooth, controlled deposition of water.
Traditionally, hot water has been used because it slightly melts the layer of ice below it, leading some operators to believe it forms a stronger bond during the freezing process because heating the water releases dissolved gases thus allowing the ice to freeze in a clearer state as well as reduces the freezing time of the water due to the Mpemba effect. The water used in some rinks is also filtered and treated before being used in the ice resurfacer to remove any minerals or chemicals in the water. These impurities can otherwise make the ice brittle, soft, give it undesirable odors, or change the color and clarity.
Many ice resurfacers are fitted with a "board brush", a rotary brush powered by a hydraulic motor. The board brush is extended and retracted on the left side of the machine by a hydraulic arm. This allows the operator to collect ice shavings and debris that accumulate along the edge of the rink where the conditioner cannot easily reach. The brush sweeps the accumulations into the path of the conditioner, which removes them from the ice. The use of a board brush can dramatically reduce the need for edging of the rink. After resurfacing the entire sheet, also known as an "ice cut" or "flood", the snow container must be emptied. Hydraulics raise one end of the container, causing the snow to spill out.
Smaller, cheaper machines have also been designed to provide a smooth ice surface in a manner similar to a traditional resurfacer. These can be either self-propelled or pushed/pulled by the operator. Self-propelled vehicles typically incorporate the main components of full-size ice resurfacer, including a blade and water tank, but on a smaller scale. These are usually mounted to an ATV or golf cart-like vehicle.

Ice edgers

The ice around the edges of a rink has a tendency to build up because the conditioner blade does not extend all the way to the outer edges of the conditioner and it is unwise to "ride" the dasher boards. An ice edger is a small device similar to a rotary lawn mower that is used to shave down the edges of the ice surface that the ice resurfacer cannot cut. An ice edger cannot shave ice that has an overall bowl or mushroom shape.
Drivers using latest model ice resurfacing equipment can effectively cut ice edges within millimeters of the dasher board.

In popular culture