Honey extraction


Honey extraction is the central process in beekeeping of removing honey from honeycomb so that it is isolated in a pure liquid form.
Normally, the honey is stored by honey bees in their beeswax honeycomb; in framed bee hives, the honey is stored on a wooden structure called a frame. The honey frames are typically harvested in the late summer, when they will be most filled with honey. On a completely filled frame, the cells will be capped over by the bees for storage; that is, each cell containing honey will be sealed with a capping made of beeswax.

Centrifugal extraction

This is widely used, especially by commercial beekeepers. Most centrifugal extractors are not suitable for natural combs. This form of extraction is therefore closely associated with vertical hives, which since the mid 1800s have been the most common variety of hive, and are normally furnished with frames including artificial support. Significant labour is required to disassemble the hives and process the honey, then clear up the mess, so it is usual to extract honey from each hive only once a year.
The first step in the extraction process is to break or remove all of the cappings. This may be accomplished using an automated uncapper machine or with a manually-operated uncapping knife. Usually, these tools are used together, along with a pronged cappings fork. To facilitate cutting off these wax cappings, the knife is often heated. The removed bits of wax, called cappings, are rich in honey which can be slowly drained off with the help of some heating. This 'cappings wax' is very valuable and often used to make candles or other products. Automated uncapping machines normally work by abrading the surface of the wax with moving chains or bristles or hot knives. This, while messy, makes the process easier than doing this task manually.
Some beekeepers will also harvest the propolis, a resinous material bees gather to glue the frames together; propolis is used for its supposed medicinal properties.
Once uncapped, the frames are then placed in a honey extractor, which spins them so that most of the honey is removed by centrifugal force. Care must be taken to ensure that all frames are loaded correctly, as the comb is angled slightly upwards to prevent the honey flowing out; if loaded incorrectly, this can also prevent the honey flowing out during extraction. Once extracted, the resulting honey will contain bits of wax and must be passed through a screen so that clean liquid honey results.
Any honey that can't be harvested, which includes crystallized honey left on the frames after extraction, or honey that is not capped over, and therefore unripened, is usually placed back into the colonies for the bees to clean up. Some beekeepers place wet frames outside so that it will be reclaimed by the bees. This must be done early in the morning or late in the evening as the bees will aggressively harvest such a rich source. Care must be taken so that this is done at a time when food is not scarce, or else bees from differing colonies will fight over the honey. In addition, this can spread disease from contaminated frames and can be a potential problem; this technique is not advised.
The extraction process is typically done inside a specialized room, or honey house, that can be heated, with all of the necessary tools nearby and is washable. The room must be well sealed, as bees will eagerly try to enter and gather the honey. It is important to remember that honey is a food product.
The table below outlines the extraction process.
Honey Harvest Process stepsMethod descriptionAlternative Method 1Alternative Method 2
1Remove hive outer cover from top of the beehive super
2Remove hive inner cover from top super
3If no queen excluder was used, inspect frames for brood and only remove frames that are without brood.Remove only frames that are 80% capped and without broodRemove all frames that have honey but no brood
4aAdd fume board to top of hive to force bees into lower parts of hive.Remove super and use air blower to force bees from framesRemove frames one by one and manually brush off bees
4bRepeat steps 3 and 4a until all supers are removed
5Transport frames in supers to honey house
6Heat and dehumidify frames in honey house for 1– 2 daysDo nothing
7Use refractometer to check that moisture content is below 18.5%Do nothing
8Remove the wax cap on capped honey manually Uncap mechanicallyCut out comb honey
9Load honey extractorLoad honey pressSet comb honey chunks on drip pan to drain off honey from cutting edge
10Turn on honey extractor motorManually turn extractor crank
11Run extracting process for several minutes
12Remove extracted frames from extractor
13Empty extractor sump: Let collected honey flow into storage container via gravity.Empty extractor sump: Pump honey using a mechanical pump
14Filter honeyLet wax and other particles settle outRun raw honey through a separator
15Grade honeyDo nothing
16Bottle honeyPackage comb honey
17Market and sell honeyUse honey for home consumption

Crush and drain

This method is usual for natural comb without artificial support. Such combs are associated with top-bar hives, especially horizontal hives which allow for continuous harvest through the season.
StepWarré hiveTrough top bar hive
1Remove roof and quiltRemove cover
2Remove boxes of comb from the top of the hive, being sure to leave sufficient stores for the colony to overwinter on.Remove mostly full combs.

Once the combs are removed from the hive, they can be processed in several ways:
consist of plastic honeycomb lattice. Bees fill in the vertical gaps with beeswax and the cells with honey. When the combs are full of ripe honey, the mechanism of the frames is activated, the vertical gaps are moved to offset by one half of a cell. This breaks the wax seal and allows the honey to flow down through the cells into a channel at the base of each frame and out into a collection vessel. The bees normally show no sign of disturbance, and any bees in the flow frame at the time are not harmed. Clean honey can be produced and filtration is not normally required. The system is then reset and the bees clean up any remaining honey, remove the capping, and refill the cells, beginning the process again.
Each colony that is to use flow frame extraction must be furnished with flow frames, and their cost limits their appeal to existing commercial apiarists. However, new entrants to small beekeeping may find that the greater cost per hive of flow frames is more than off-set by saving time, labour, space, mess, and disturbance to the bees. Expensive extraction equipment is not required.