ExpressCard


ExpressCard, initially called NEWCARD, is an interface to connect peripheral devices to a computer, usually a laptop computer. The ExpressCard technical standard specifies the design of slots built into the computer and of expansion cards to insert in the slots. The cards contain electronic circuits and sometimes connectors for external devices. The ExpressCard standard replaces the PC Card standards.
ExpressCards can connect a variety of devices to a computer including mobile broadband modems, IEEE 1394 connectors, USB connectors, Ethernet network ports, Serial ATA storage devices, solid-state drives, external enclosures for desktop-size PCI Express graphics cards and other peripheral devices, wireless network interface controllers, TV tuner cards, Common Access Card readers, and sound cards.

Standards

Originally developed by the Personal Computer Memory Card International Association, the ExpressCard standard is maintained by the USB Implementers Forum. The host device supports PCI Express, USB 2.0, and USB 3.0 connectivity through the ExpressCard slot; cards can be designed to use any of these modes. The cards are hot-pluggable. The ExpressCard standard is an open standard by ITU-T definition, and can be obtained from the USB-IF website free of charge.
USB-IF administers the ExpressCard Compliance Program, under which companies earn the right to obtain a license to use the ExpressCard logo on their compliant products.

Form factors

The ExpressCard standard specifies two form factors, ExpressCard/34 and ExpressCard/54 —the connector is the same on both. Standard cards are long and thick, but may be thicker on sections that extend outside the standard form for antennas, sockets, etc. With its 75 mm standard length, the ExpressCard will protrude 5 mm over the holder's surface, whereas a variant with 70 mm length remains level with the surface.

Comparison to other standards

The older PC Cards came in 16-bit and the later 32-bit CardBus designs. The major benefit of the ExpressCard over the PC card is more bandwidth, due to the ExpressCard's direct connection to the system bus over a PCI Express ×1 lane and USB 2.0, while CardBus cards only interface with PCI. The ExpressCard has a maximum throughput of 2.5 Gbit/s through PCI Express and 480 Mbit/s through USB 2.0 dedicated for each slot, while all CardBus and PCI devices connected to a computer usually share a total 1.06 Gbit/s bandwidth.
The ExpressCard standard specifies voltages of either 1.5 V or 3.3 V; CardBus slots can use 3.3 V or 5.0 V. The ExpressCard FAQ claims lower cost, better scalability, and better integration with motherboard chipset technology than Cardbus. PCMCIA devices can be connected to an ExpressCard slot via an adapter.
When the PC Card was introduced, the only other way to connect peripherals to a laptop computer was via RS-232 and parallel ports of limited performance, so it was widely adopted for many peripherals. More recently, virtually all laptop equipment has 480 Mbit/s Hi-Speed USB 2.0 ports, and most types of peripheral which formerly used a PC Card connection are available for USB or are built-in, making the ExpressCard less necessary than the PC Card was in its day. Some laptop computers do not have an ExpressCard slot.

Availability

An ExpressCard slot had been commonly included on high-end laptops made since 2006:
Because of the lack of backward compatibility, some laptop manufacturers initially released models incorporating both CardBus and ExpressCard slots. These included certain models of Acer Aspire, Acer Extensa, Toshiba Satellite, Dell Latitude and Precision, MSI S42x and Lenovo ThinkPad Z60m, R52, T60, R61 and T61.
In March 2005, the Personal Computer Memory Card International Association showed some of the first ExpressCard products at the CeBIT trade show in Germany. A large number of ExpressCard devices were presented.


In November 2006, Belkin announced that it was launching the first ExpressCard docking station, which uses the PCIe part of an ExpressCard connection to enable 1600x1200 video and the USB part to provide USB, audio and network ports. This points to the ability for ExpressCard to allow more capable non-OEM docking stations for laptop computers.
In 2007, Sony introduced its Vaio TZ model, which incorporates ExpressCards. Also the Sony Vaio FZ and Vaio Z series have the ExpressCard/34 Slot integrated in them. Sony also uses the ExpressCard/34 form factor for the flash memory modules in its XDCAM EX/SxS based camcorders, making the copying of video data between these cameras and ExpressCard-equipped laptops easier. For this reason, Sony also offers a USB-based SxS reader for desktop computers.
The new Toshiba Satellite P and X 200/205 series of laptops and desktop replacements have an ExpressCard/34 slot since April 2007. In P200 series it's a /54 size not /34.
Ever since PCMCIA disbanded in 2009, newer laptops from 2010 on more commonly do not include ExpressCard slots except for some business-oriented models. For WWAN connectivity cards, either mini-PCIe slots or USB connected variants have become the preferred connection methods. For external desktop graphics card enclosures and other peripherals that interface with PCI Express, Thunderbolt has supplanted ExpressCard in that role due to its faster speed and ability to use multiple PCIe 2.0 lanes; the first and second Thunderbolt revisions offered 20Gbit/s of maximum bandwidth with four PCIe 2.0 lanes while ExpressCard could only muster 5Gbit/s maximum with one PCIe 2.0 lane.

ExpressCard 2.0

The ExpressCard 2.0 standard was introduced on March 4, 2009, at CeBIT in Hannover. It provides a single PCIe 1.0 2.5 GT/s lane and a USB 3.0 "SuperSpeed" link with a raw transfer speed of 5 Gbit/s. It is forward and backward compatible with earlier ExpressCard modules and slots. ExpressCard 2.0 products were expected to be in the market by late 2010.
USB 3.0 SuperSpeed compatibility is achieved by sharing the pins with the PCIe link. An inserted card signals which mode should be used.