Dynamic soaring


Dynamic soaring is a flying technique used to gain energy by repeatedly crossing the boundary between air masses of different velocity. Such zones of wind gradient are generally found close to obstacles and close to the surface, so the technique is mainly of use to birds and operators of radio-controlled gliders, but glider pilots are sometimes able to soar dynamically in meteorological wind shears at higher altitudes.
Dynamic soaring is sometimes confused with slope soaring which is a technique for achieving elevation.

Basic mechanism

While different flight patterns can be employed in dynamic soaring, the simplest is a closed loop across the shear layer between two airmasses in relative movement. The gain in speed can be explained in terms of airspeed or groundspeed:
The energy is extracted by using the velocity difference between the two airmasses to lift the flying object to a higher altitude after the transfer between the airmasses.
In practice, there is a turbulent mixing layer between the moving and stationary air mass. In addition, drag forces are continually slowing the plane. Since higher speed gives rise to higher drag forces, there is a maximum speed that can be attained. Typically around 10 times the windspeed for efficient glider designs.
When seabirds perform dynamic soaring, the wind gradients are much less pronounced, so the energy extraction is comparably smaller. And instead of doing circles as glider pilots do, the birds will execute a series of half circles in opposite directions, i.e. perform a slalom flight. A bird may begin by climbing though the gradient while facing into the increasing wind to gain altitude, and then make a 180° turn clockwise. This would be followed by a dive back down through the gradient, increasing its airspeed as it moves into slower air at lower altitude. The cycle would then be completed by making an anti-clockwise turn at low altitude to face back into the wind. This has the effect of transporting the bird laterally to the wind. Ideally it can travel cross wind indefinitely by continuing to execute this maneuver.

As drag is slowing the bird, dynamic soaring is a tradeoff between speed lost to drag, and speed gained by moving through the wind gradient. At some point, climbing higher carries no additional benefit, as the wind gradient lessens with altitude.

Birds

es are particularly adept at exploiting these techniques and can travel hundreds of miles using very little energy. Birds that soar dynamically have a skeletal structure that allows them to lock their wings when they are soaring, to reduce muscle tension and effort besides steering.
Lord Rayleigh first described dynamic soaring in 1883 in the British journal Nature:
The first case described above by Rayleigh is simple gliding flight, the second is static soaring, and the last is dynamic soaring.

Manned aircraft

In his 1975 book Streckensegelflug, Helmut Reichmann describes a flight made by Ingo Renner in a Glasflügel H-301 Libelle glider over Tocumwal in Australia on 24 October 1974. On that day there was no wind at the surface, but above an inversion at 300 metres there was a strong wind of about 70 km/h. Renner took a tow up to about 350 m from where he dived steeply downwind until he entered the still air; he then pulled a 180-degree turn and climbed back up again. On passing through the inversion he re-encountered the 70 km/h wind, this time as a head-wind. The additional air-speed that this provided enabled him to recover his original height. By repeating this maneuver he successfully maintained his height for around 20 minutes without the existence of ascending air, although he was drifting rapidly downwind. In later flights in a Pik 20 sailplane, he refined the technique so that he was able to eliminate the downwind drift and even make headway into the wind.

Unmanned aircraft

The dynamic soaring technique is adapted in unmanned aerial vehicles for enhancing their performance under a thrust-off condition. This improves the endurance and range of the aircraft in austere conditions.

Radio-controlled glider

In the late 1990s, radio-controlled gliding awoke to the idea of dynamic soaring. Radio-controlled glider pilots perform dynamic soaring using the leeward side of ground features such as ridges, saddles, or even rows of trees. If the ridge faces the wind, and has a steep back side, it can cause flow separation off the top of the hill, resulting in a layer of fast air moving over the top of a volume of stagnant or reverse-flow air behind the hill. The velocity gradient, or wind shear, can be much greater than those used by birds or full scale sailplanes. The higher gradient allows for correspondingly greater energy extraction, resulting in much higher speeds for the aircraft. Models repeatedly cross the shear layer by flying in a circular path, penetrating a fast-moving headwind after flying up the back side, turning to fly with the wind, diving down through the shear layer into the stagnant air, and turning again to fly back up the back side of the hill. The loads caused by rapid turning at high speed require significant structural reinforcement in the fuselage and wing. Because of this, dynamic soaring models are commonly built using composite materials.
As of June 2018, the highest reported ground speed for radio control dynamic soaring was. There is no official sanctioning organization that certifies speeds, so records are listed unofficially based on readings from radar guns, although analysis from video footage and other sources is also used. Lately, some models have begun carrying on-board telemetry and other instruments to record such things as acceleration, air speed, etc.