Diversity combining


Diversity combining is the technique applied to combine the multiple received signals of a diversity reception device into a single improved signal.

Various techniques

Various diversity combining techniques can be distinguished:
Sometimes more than one combining technique is used – for example, lucky imaging uses selection combining to choose the best 10% images, followed by equal-gain combining of the selected images.
Other signal combination techniques have been designed for noise reduction and have found applications in single molecule biophysics, chemometrics among other disciplines.

Timing combining

When the focus is on the wireless transmission of longer signal sequences, such as for example Ethernet packets, specific performance characteristics regarding diversity gain on a parallel redundant wireless transmission system can be observed.
For "timing combining", data packets are redundantly and simultaneously sent over parallel paths. On the receiving side, out of the branches the first arriving packet is selected and immediately processed towards the end application. Further copies of the packet -if arriving- are discarded. This type of postdetection combiner is called a "timing combiner", since a significant performance improvement is gained through the immediate processing of the first arriving packet.

Switched combining two-way radio example

In land-mobile radio, where vehicle-mounted and hand-held radios communicate with a base station radio over a single frequency, space diversity is achieved by having several receivers at different sites. Diversity combining, or voting, in two-way radio systems is a method for improving talk-back range from walkie-talkie and vehicular mobile radios. The receivers are connected to a device referred to as a voting comparator or voter.
The voting comparator performs an evaluation of all received signals and picks the most usable received signal. In repeater systems, the voted signal is retransmitted. In simplex systems, it goes to the console speaker at the base station. Audio from a receiver that is not voted is ignored. Voting comparators in analog FM systems can switch between receivers in tenths- or hundredths-of-a-second,. So long as an intelligible signal gets to a single receiver in the system, the repeated audio, or audio sent to the console speaker, would be intelligible.
In this arrangement, receivers at remote sites are connected to the voting comparator by private telephone lines, a channel in a D4 channel bank on a DS1, or an analog microwave baseband channel.

How signals are evaluated

The earliest voting comparators relied on a tone encoded on a separate audio path, requiring each receiver site to have a 4-wire circuit or two audio paths. The pitch of the tone changed to represent the received signal level, or FM receiver limiter voltage, at the remote receiver. This worked poorly because it did not account for microwave baseband noise or noisy telephone company circuits.
Newer voting comparators compare signal-to-noise ratio at the voting comparator, accounting for end-to-end noise, bad phone lines, poor level discipline, as well as the best diversity reception path.

Walkie-talkie talk-back range

When communicating with hand-held radios, base stations generally talk out further than they can receive. Voting among several receivers at different sites increases the probability that one of the receivers will acquire a usable signal from two-way radios in a system.

Interference reduction

Diversity combining reduces one possible single-point failure: any single receiver failure, or local interference to a single receiver, will not block reception on the entire system. Equipment sites can host many radio transmitters and receivers. A single site is subject to local, site-specific interfering signals. These interfering signals may come and go as transmitters switch on and off.
A potential problem with receivers located at high-elevation receiver sites is that they may acquire signals from distant counties, prefectures, or other provinces. These unwanted, distant signals can be stronger than desired signals from local walkie-talkies. The distant signals may block local weak signals in some cases. Having several receive sites increases the probability that one of the sites will receive the local signal in the presence of a distant, undesired one. Selective calling can eliminate users having to listen to the audio of distant signals even though the distant signals are within receive range of one or more receivers.

Coverage

A minimum of 95% coverage is cited in literature for critical or emergency service two-way radio systems. One definition of system coverage is Telecommunications Industry Association TSB-88A standard.

Vote-lock or vote-and-hold option

The majority of installations using diversity combining equipment continually evaluate the best received signal against all other signals. Throughout the length of a received transmission, the comparator may switch receivers as often as every few tenths of a second. As a walkie-talkie user causes a signal fade by turning their head, or a passing tractor-trailer rig blocks their signal at the voted receive site, the combining unit rapidly changes to a different receiver.
In some installations, diversity combining equipment is configured to lock on a receiver. For example, in some rural, regional coverage systems, the receivers each cover a unique geographic area. There is not much overlap. If the system consisted of two sites, north and south, it would pick the better of the two and remain locked on that receiver until the transmission ended. This works better with mobile radios because their signal strengths tend to be steady.
In some cases this vote-and-hold is used to steer transmitter selection. Consider the case of a regional system with two base stations: north and south. If the diversity combining equipment votes "north," the next time the dispatcher presses the transmit button, the north transmitter will key. Called transmitter steering, this is supposed to automate transmitter selection in systems where more than one transmitter site is available. In some instances it doesn't work well.
In mobile data systems, the vote lock option is preferred because constant switching between receivers causes lost data packets. The diversity combining equipment switches fast enough that syllables are not lost but not fast enough that bits are not lost. Mobile data systems usually originate with modems in mobile radios. Mobile radios usually produce solid signals into more than one receive site, so the signal strengths are strong enough for vote locking to work well.