There were three DEC 3000 model families, codenamed Pelican, Sandpiper, and Flamingo. Within Digital, this led to the DEC 3000 series being affectionately referred to as "the seabirds".
Note: Server configurations of the Model 400/500/600/700/800/900 systems were suffixed with "S".
Description
The logic in Flamingo- and Sandpiper-based systems are contained on two modules, the CPU module and the I/O module, with the CPU module being the largest board. The two modules are connected via a 210-pin connector. The logic in Pelican-based systems are contained the CPU module and system module. The CPU module is a daughterboard that plugs into the system module and contains the CPU and the B-cache. The architecture of the Flamingo- and Sandpiper-based systems is based around a crossbar switch implemented by an ADDR ASIC, four SLICE ASICs and a TC ASIC. These ASICs connect the various different width buses used in the system, allowing data to be transferred to the different subsystems. PALs were used to implement the control logic. The cache, memory and TURBOchannel controllers, as well as other control logic, is entirely implemented by PALs. Pelican-based systems have an entirely different architecture from the other systems, similar to that of late-model Personal DECstations that they are based on, with a traditional workstation architecture with buses and buffers.
Memory
The Sandpiper and Flamingo used proprietary 100-pin, 40-bit Fast Page Mode SIMMs with capacities of 2 MB, 4 MB, 8 MB, 16 MB or 32 MB. These were eight-way interleaved, providing a 256-bit-wide bus to memory. The Sandpiper had two such eight-SIMM banks, for up to 512 MB total system RAM, while the Flamingo had four banks and supported up to 1 GB. In comparison, the Pelican was a budget architecture utilising eight standard 72-pin Fast Page Mode SIMMs that were protected with longword parity instead of ECC, with capacities of 8 MB or 32 MB, for a total of up to 256 MB RAM. These were two-way interleaved, for a 64-bit-wide bus to memory.
Expansion slots
The DEC 3000 AXP series uses the 32-bit TURBOchannel bus running at various speeds, 12.5 MHz in the 300 models, 22.5 MHz in the 400 models and 25 MHz in models 500 to 900. The TURBOchannel bus is provided by an ASIC, which connected it to the SLICE data path ASICs. The number to expansion slots also varied, the 300 models had two slots, except for the 300L, which had none. Models 400, 600 and 700 had three slots, the model 500X featured five, while models 500, 800 and 900 featured six.
Graphics
The Model300 Series and the Model 500, 500S and 500X feature integrated graphics provided by the CXTurbo subsystem, which resides on the system module. This subsystem is essentially an onboard HX TURBOchannel option module. The subsystem features a SFB ASIC, a Brooktree Bt459 RAMDAC, 2 MB of VRAM and in the Model 500, 500S and 500X, a 256 KB flash ROM that holds part of the system firmware. The CXTurbo subsystem can reach resolutions of 1280 × 1024 at 72 Hz in the 300, 300X and 300LX models, 1024 × 768 at 72 Hz in the Model 300L and 1280 × 1024 at 66 Hz or 72 Hz in the Model 500, 500S and 500X. Because of the DEC 3000 AXP's similarity with Digital's previous RISC workstation line, the DECstation, the same TURBOchannel graphics options, which consisted of framebuffers, 2D and 3D accelerated graphics, were carried over the DEC 3000 AXP. Like the DECstation, up to three framebuffers of the same model can be installed in a single system to support multiscreen configurations. Despite using the same graphics options as the DECstation at introduction, later options for the DEC 3000 AXP were designed exclusively for the platform. These options were Digital's ZLX-E1/E2/E3, ZLX-L1/L2 and ZLX-M1/M2 series of PixelVision architecture-based 2D/3D accelerated graphics and Kubota's high-end 3D accelerated graphics subsystem, the Denali. The Denali is an external enclosure that contains up to six geometry engines and multiple memory modules. It was capable of advanced 3D graphics, such as interactive volume rendering. It connects to the DEC 3000 AXP via a cable and a TURBOchannel interface module.
I/O subsystem
The I/O subsystem provides the DEC 3000 AXP with Ethernet, ISDN and audio capability, four serial lines, and a real time clock. The I/O subsystem is interfaced to TURBOchannel by the IOCTL ASIC, which also implements two 8-bit buses, known as IOBUS HI and IOBUS LO, to which the I/O devices connect to. These two 8-bit buses can be combined to serve as one 16-bit bus to provide an I/O device with more bandwidth. Ethernet is provided by an AMDAm7990 LANCE, an AMD Am7992 SIA that implements the 10BASE-T or AUI Ethernet interface, and an ESAR that stores the MAC address. The Am7990 is the only I/O device in the subsystem to have a 16-bit interface to the IOCTL ASIC. ISDN and telephone-quality audio is provided by an AMD Am79C30A DSC. The four serial lines are provided by two Zilog Z85C30 SCC dual UARTs, and the real time clock is a Dallas Semiconductor DS1287A.
The DEC 3000 AXP used a TCDS ASIC to provide an interface between the SCSI controllers and the TURBOchannel bus. Early systems used one or two NCR53C94 SCSI controllers, which provided one or two 5 MB/s 8-bit single ended SCSI buses. Later and higher end systems such as the Model 600, 700, 800 and 900 also feature two SCSI controllers, but used the NCR 53CF94-2 instead, which provided faster 10 MB/s 8-bit single ended SCSI buses.
