Coherent optical module refers to a typically hot-pluggable coherent optical transceiver that uses coherent modulation and is typically used in high-bandwidth data communications applications. Optical modules typically have an electrical interface on the side that connects to the inside of the system and an optical interface on the side that connects to the outside world through a fiber optic cable. The technical details of coherent optical modules were proprietary for many years, but have recently attracted efforts by multi-source agreement groups and a standards development organizations such as the Optical Internetworking Forum. Coherent optical modules can either plug into a front panel socket or an on-board socket. Coherent optical modules form a smaller piece of a much larger optical module industry.
Electrical Interface Types
There are multiple variants of the electrical interface of coherent optical modules use.
Analog Coherent Optics (ACO)
The Optical Internetworking Forum in 2016 published the CFP2-ACO or CFP2 - Analog Coherent Optics Module Interoperability Agreement. This IA supports a configuration where the digital signal processor is on the main board and analog optical components are on the module. This IA is useful in the case when the DSP exceeds the module power envelope. The ACO interface can be used in coherent optics applications when the link delivers a flexible amount of bandwidth to the system, for example when combined with FlexE. The initial ACO IA is for the CFP2 module. The typical optical modulation that are used include Dual Polarization Quadrature Phase Shift Keying and QAM-16.
Digital Coherent Optics (DCO)
These modules put the DSP on the module and use a conventional retimed digital interface. These modules can use the same optical modulation techniques as the ACO interfaces do.
Optical modulation and multiplexing types
Many different forms of optical modulation and multiplexing have been employed in coherent optical modules.
NRZ and PAM-4 modulation
Some coherent optical modules can fall back to older, simpler modulation techniques such as on-off keying and/or Pulse-amplitude modulation with 4 levels when appropriate. This is used, for example, when it is discovered that the module on the other end of the link does not support coherent modulation.
Tunable lasers are sometimes used in combination with coherent modulation to allow a module to support various forms of network-based optical switching such as needed in certain cases by an optical mesh networks or a Reconfigurable optical add-drop multiplexer. In these, the transmit laser can be tuned to a different optical frequency/wavelength. Similarly the receiver is able to receive different optical frequencies.
Lambda multiplexing
Different optical wavelengths, also referred to as lambdas, of light are multiplexed within some coherent optical modules using wavelength-division multiplexing. Variants include Coarse WDM, Dense WDM.
In-module components
Coherent optical modules have a series of components inside, some of which have received attention from standards development organizations.
In-module gearbox
In many cases, the baud rate of the coherent optical interface does not equal the baud rate of the electrical interface. In these cases, a gearbox may be used within the module to convert between the rates. Since coherent modules typically have Digital Signal Processors, these gearbox functions are sometimes implemented in firmware.
Particularly in the long-reach module market, in-module Forward Error Correction has been included. This has been in both proprietary and standards-based forms. Coherent optical modules sometimes have used Soft-decision decoder FEC algorithms
The OIF has created interoperability agreements to create multi-vendor interoperability for a series of in-module components, particularly focused on coherent transmission. These have included
High Bandwidth Integrated Polarization Multiplexed Quadrature Modulators
The OIF has created interoperability agreements to create multi-vendor interoperability for the tunable lasers that are sometimes used in optical modules. These have included
Integrable Tunable Laser Assembly Multi Source Agreement
Some pluggable modules fit on top of the printed circuit board instead of on the front panel.
CFP family on-board modules
MSA 5″×7″
MSA 4″×5″
Users of Coherent optical Modules
Long-haul Optical Transport Network networks were the traditional users of coherent modulation. Cloud scale data centers have become an important consumer of coherent optical modules, particularly in the Ethernet connectivity space for reaches greater than 10 km where the advantages of coherent modulation can outweigh the increased cost.
Optical module focused trade shows
The main trade show for the coherent optical module industry is the Optical Fiber Conference, that is held annually in southern California. Other prominent shows for the industry include ECOC in Europe and FOE in Japan.
