All-way stop


An all-way stop – also known as a four-way stop – is a traffic management system which requires vehicles on all the approaches to a road intersection to stop at the intersection before proceeding through it. Designed for use at low traffic-volume locations, the arrangement is common in the United States, Canada, South Africa, and Liberia, as well as in a number of, usually rural, locations in Ireland where visibility on the junction approaches is particularly poor. The stop signs at such intersections may be supplemented with additional plates stating the number of approaches.

Operation

In most jurisdictions of the United States, the rules of the all-way stop are the same. A motorist approaching an all-way stop is always required to come to a full stop behind the crosswalk or stop line. Pedestrians always have the priority to cross the road, even if the crosswalk is not marked with surface markings.
Driving instructors suggest that communication is always vital—including the use of turn signals to indicate which direction you intend to turn. Often, vehicles are able to make compatible moves at the same time without following the order listed above. If it is not clear who has the right-of-way, drivers should use good judgement until they clear the intersection. Within some U.S. jurisdictions, such as the state of Idaho, bicyclists are exempt from the need to make a complete stop, but must give way to other vehicles as otherwise required by law.

Application

In the United States, the Federal Highway Administration's Manual on Uniform Traffic Control Devices defines the standards commonly used for the application of all-way stops. Where a stop has been determined to qualify, it is signed at all approaches to the intersections with a standard octagonal "Stop" sign, with a supplemental "All-Way" plate. Earlier editions of the MUTCD allowed supplemental plates specifying the number of approaches in an all-way stop, as in "2-Way", "3-Way" or "4-Way". According to the MUTCD, installation of an all-way stop should be based on a traffic engineering study to determine if minimum traffic volume or safety criteria are met. These intersections are often found where roads have light-volume traffic which does not justify a traffic light.
An all-way stop may also be justified if the intersection has shown a history of collisions involving pedestrians or vehicles. All-way stops may also be used as an interim measure preceding the placement of a traffic light, to provide a low-speed area for pedestrians to cross, where a cross street experiences considerable difficulty finding safe gaps due to heavy traffic volumes, or where traffic is frequently delayed by turning conflicts. Additionally, the MUTCD advocates the placement of all-way stops at intersections between through roads in residential areas if an engineering study can show that traffic flow would be improved by installing it. Despite published guidelines, all-way stops are routinely placed by jurisdictions due to political pressure from adjacent residents. Intersections between two minor highways with similar traffic counts, two collector roads in an urban or suburban setting or a collector road and a local road in a busy setting are the most common locations for an all-way stop.
Traffic signals will sometimes flash red indications in all directions following a malfunction, or all-red flashing operation may be scheduled to reduce delay or handle construction activity or unusual traffic patterns. When a traffic signal flashes in all-red mode, it legally operates as an all-way stop. When all approaches to an intersection are controlled in this way the rules for an all-way stop apply. Traffic signals may also flash yellow to major directions and flash red to minor directions during off-peak times to minimize traffic delays, in which case only side-street traffic is required to stop and yield the right of way to crossing traffic on the major street.
During electrical outages when a traffic signal does not display any indications including flashing red, some jurisdictions require that the intersection be treated as an all-way stop. Other jurisdictions treat a dark signal as an uncontrolled intersection, where standard rules of right-of-way apply without the requirement of a complete stop.

Benefits and disadvantages

The main reason for the use of stop signs at road junctions is safety. According to an international study of locations where the system is in use, all-way stop control applied to four-legged intersections may reduce accident occurrence by 45%. However, given alternative methods of intersection control and some of the disadvantages of all-way stops, the Handbook of Road Safety Measures recommends that four-way stops are best used between minor roads away from urbanized areas. Another benefit of all-way stops is assurance that vehicles enter the intersection at a low speed and have more time to take heed of the traffic situation, especially useful when sight distance is highly restricted.
Some of the disadvantages associated with all-way stops are:
Few countries outside North America – least of all, those in Europe – have intersections at which all users must stop at all times; the conditions for stop sign placement may indeed preclude such an arrangement in many places. In Sweden all-way stops have been tested since the 1980s but are little used even though they are now permitted. In the UK they have always been very uncommon and were formally prohibited by the Department for Transport in 2002.
Four-way stops are common in the Southern African Development Community area, with priority going to the first vehicle to arrive and stop at the line.
At four-legged intersections within Europe, a roundabout or mini-roundabout is commonly used to assign a relative priority to each approach. Alternatively, at smaller intersections, priority to the right is widely used in most countries.