Air pollutant concentrations


Air pollutant concentrations, as measured or as calculated by air pollution dispersion modeling, must often be converted or corrected to be expressed as required by the regulations issued by various governmental agencies. Regulations that define and limit the concentration of pollutants in the ambient air or in gaseous emissions to the ambient air are issued by various national and state environmental protection and occupational health and safety agencies.
Such regulations involve a number of different expressions of concentration. Some express the concentrations as ppmv and some express the concentrations as mg/m3, while others require adjusting or correcting the concentrations to reference conditions of moisture content, oxygen content or carbon dioxide content. This article presents methods for converting concentrations from ppmv to mg/m3 and for correcting the concentrations to the required reference conditions.
All of the concentrations and concentration corrections in this article apply only to air and other gases. They are not applicable for liquids.

Converting air pollutant concentrations

The conversion equations depend on the temperature at which the conversion is wanted. At an ambient sea level atmospheric pressure of 1 atm, the general equation is:
and for the reverse conversion:
where:
mg/m3= milligrams of pollutant per cubic meter of air at sea level atmospheric pressure and T
ppmv= air pollutant concentration, in parts per million by volume
T= ambient temperature in K = 273. + °C
0.082057338= Universal gas constant in L atm mol⁻¹ K⁻¹
M= molecular mass of the air pollutant

Notes:
Air pollutant concentrations expressed as mass per unit volume of atmospheric air at sea level will decrease with increasing altitude. The concentration decrease is directly proportional to the pressure decrease with increasing altitude. Some governmental regulatory jurisdictions require industrial sources of air pollution to comply with sea level standards corrected for altitude. In other words, industrial air pollution sources located at altitudes well above sea level must comply with significantly more stringent air quality standards than sources located at sea level. For example, New Mexico's Department of the Environment has a regulation with such a requirement.
The change of atmospheric pressure with altitude can be obtained from this equation:
Given an air pollutant concentration at sea-level atmospheric pressure, the concentration at higher altitudes can be obtained from this equation:
As an example, given an air pollutant concentration of 260 mg/m3 at sea level, calculate the equivalent pollutant concentration at an altitude of 2800 meters:
Note:
Many environmental protection agencies have issued regulations that limit the concentration of pollutants in gaseous emissions and define the reference conditions applicable to those concentration limits. For example, such a regulation might limit the concentration of Nitrogen oxide| to 55 ppmv in a dry combustion exhaust gas corrected to 3 volume percent O2 in the dry gas. As another example, a regulation might limit the concentration of total particulate matter to 200 mg/m3 of an emitted gas corrected to a dry basis and further corrected to 12 volume percent CO2 in the dry gas.
Environmental agencies in the USA often use the terms "dscf" or "scfd" to denote a "standard" cubic foot of dry gas. Likewise, they often use the terms "dscm" or "scmd" to denote a "standard" cubic meter of gas. Since there is no universally accepted set of "standard" temperature and pressure, such usage can be and is very confusing. It is strongly recommended that the reference temperature and pressure always be clearly specified when stating gas volumes or gas flow rates.

Correcting to a dry basis

If a gaseous emission sample is analyzed and found to contain water vapor and a pollutant concentration of say 40 ppmv, then 40 ppmv should be designated as the "wet basis" pollutant concentration. The following equation can be used to correct the measured "wet basis" concentration to a "dry basis" concentration:
As an example, a wet basis concentration of 40 ppmv in a gas having 10 volume percent water vapor would have a:

Correcting to a reference oxygen content

The following equation can be used to correct a measured pollutant concentration in a dry emitted gas with a measured O2 content to an equivalent pollutant concentration in a dry emitted gas with a specified reference amount of O2:
As an example, a measured concentration of 45 ppmv in a dry gas having 5 volume % O2 is:
when corrected to a dry gas having a specified reference O2 content of 3 volume %.
Note:
The following equation can be used to correct a measured pollutant concentration in an emitted gas to an equivalent pollutant concentration in an emitted gas containing a specified reference amount of CO2:
As an example, a measured particulates concentration of 200 mg/m3 in a dry gas that has a measured 8 volume % CO2 is:
when corrected to a dry gas having a specified reference CO2 content of 12 volume %.