ACSM-321


ACSM-321 is a Belarusian large capacity low-floor trolleybus for intercity passenger transportation, mass-produced since 2003. It belongs to the third generation of trolleybuses developed by the Belkommunmash plant in Minsk.
This model of trolleybus is used in many cities of Russia, Belarus, Ukraine, Kyrgyzstan, Latvia, Moldova, Transnistria and Serbia. Of the vehicles operated in Minsk, 33% are model 321. In Moscow it is 11%.

Description

Body

Trolleybus model 321 is a two axle low-floor large capacity city bus. The vehicle has a load-bearing structure. Covering the roof and sides are high-strength galvanized steel sheets. The tube frame, the skin of the body, the underside of the vehicle, the surface of the frame, axles, and some other elements are processed with anti-corrosive enamel by French company RM. The body is also covered with a phosphate-based paint, which protects it from corrosion. The body has a life of not less than 10 years.
The front of the bus is made of fiberglass panels. The bumpers are made of steel and lined with a fiberglass shell. The bumper consists of three parts. In 2008, model 321 underwent restyling and the headlights were replaced with lighting equipment uniform with new models of MAZ trucks, made in the city of Minsk.
The windshield of the ACSM-321 is a panoramic type. The wipers are horizontal. Most ACSM-321 trolleybuses are equipped with three electronic indicator boards, one front, one rear and one on the right side. Manufacturers include "Integral", "MEMZ", "AGIT", "Selena" and "TEES".
The side mirrors are of a spherical type, equipped with anti-reflection coating and electric heating.

Electrical equipment

The motor compartment of the bus is placed in its rear overhang on the left side. The ACSM-321 can be equipped with different motors: DC-BM Russian manufacture, DC, asynchronous Czech Škoda, asynchronous Belarusian production ANT-155 and asynchronous motors of the Russian production DTA-U and ACCD-250. The buses are equipped with axles from European manufacturers such as Rába or ZF.
The buses are equipped with a pneumatic system for remote removal of the poles from the wires of the contact network. In addition, there is a manual system using ropes and drums.
For powering low voltage circuits, there is a static converter that converts an input voltage of 550 volts to 28 volts. The low-voltage power circuits use two 12-volt batteries. It is also possible to install traction batteries for stand-alone travel.

Suspension and brakes

The ACSM-321 is equipped with air suspension, front and rear. In addition to providing softness, this enables the floor to be lowered at bus stops to facilitate the entry of persons with disabilities and passengers with prams.
Brakes on the front wheels are disk or drum. In addition, the bus is equipped with an anti-lock braking system.

Interior

There are three doors of the swivel-sliding type, similar to those in the MAZ-103 bus. The 2011 version has doors similar to those in the MAZ-203 bus.
In most trolleybuses the front half of the front door is allocated to the entry and exit of the driver from the cabin. The bus has a low level floor at all the entrances, and the floor height is 36 inches above ground level. Also there is a folding ramp at the entrance to the middle door.
The interior floor is of bakelized plywood with a thickness of 12 millimeters, which is attached to the base body. The ceiling is made of plastic in gray and white colors. The handrails are made of thin steel pipe, painted with polymer paint, which improves their resistance to corrosion, mechanical wear and sunlight. The bottom rails are attached to the floor and the top rails to the ceiling. Vertical rails can be equipped with buttons to signal the driver to stop the bus on demand. Horizontal rails can be equipped with leather handles for added convenience. In 2011, the design of handrails and glass partitions was changed to match the bus MAZ-203.
The saloon has 26 seats and the full capacity of the bus is 115. Ventilation is by a large sliding window. There are no roof hatches because of the layout of electrical equipment on the roof.

It is possible to install air conditioning for the driver and for the passenger compartment. The heating system in the passenger compartment is represented by three coils, two of four kilowatts and one of six kilowatts. The driver's cab has an electric heater with a capacity of six kilowatts.

Controls

The dashboard of the bus is made in the form of semicircles, which provide the driver with quick access to all necessary controls. In the middle of the instrument panel is a block of exemplary devices. In the middle panel is a large round speedometer with electronic odometer. Left and right of the speedometer are the gauges and indicator voltage on-board network. In some trolleybuses these devices are replaced by an electronic display.
From 2011, a new panel, similar in form to the trolleybus model 420, is used. To the right and left of the exemplary devices are keys for opening and closing the doors, turning on the alarm, and controlling the direction of movement of the bus. To the left of the driver is an additional side panel, on which is placed the hand brake lever, similar to a joystick control system. Other controls on the left side of the instrument panel house the control keys for heating and ventilation, and for internal and external lighting.