2.8 cm sPzB 41


2.8 cm schwere Panzerbüchse 41 or "Panzerbüchse 41" was a German anti-tank weapon working on the squeeze bore principle. Officially classified as a heavy anti-tank rifle, it would be better described, and is widely referred to, as a light anti-tank gun.

Description

Although the sPzB 41 was classified as a heavy anti-tank rifle, its construction was much more typical of an anti-tank gun. Like the latter, it had a recoil mechanism, carriage and shield. The only significant feature the weapon had in common with anti-tank rifles was a lack of elevation and traverse mechanisms—the light barrel could be easily manipulated manually.
The design was based on a tapering barrel, with the caliber reducing from 28 mm at the chamber end to only 20 mm at the muzzle. The projectile carried two external flanges; as it proceeded toward the muzzle, the flanges were squeezed down, decreasing the diameter with the result that pressure did not drop off as quickly and the projectile was propelled to a higher velocity. The barrel construction resulted in a very high muzzle velocity - up to 1,400 m/s. The bore was fitted with a muzzle brake. The horizontal sliding breech block was "quarter-automatic": it closed automatically once a shell was loaded. The gun was equipped with an open sight for distances up to 500m; a telescopic sight, the ZF 1х11 from the 3.7 cm Pak 36 anti-tank gun, could also be fitted.
The recoil system consisted of a hydraulic recoil buffer and spring-driven recuperator. The carriage was of the split trail type, with suspension. Wheels with rubber tires could be removed, making the gun significantly lower and therefore easier to conceal; the process took 30–40 seconds. The guns' construction allowed toolless dismantling to five pieces, the heaviest of which weighed 62 kg.

Development and production history

The cone-bore principle was first patented in 1903 by a German designer, Karl Puff. In the 1920s and 1930s, another German engineer, Gerlich, conducted experiments with coned-bore barrels that resulted in an experimental 7 mm anti-tank rifle with a muzzle velocity of 1,800 m/s.
Based on these works, Mauser-Werke AG developed a 28/20 mm anti-tank weapon initially designated Gerät 231 or MK.8202 in 1939–1940. In June–July 1940, an experimental batch of 94 pieces was given to the army for trials. They resulted in some modifications and in 1941 mass production of what became 2.8 cm schwere Panzerbüchse 41 started. One piece cost 4,520 Reichsmarks. The last gun was built in 1943; the main reason for the discontinuance was the lack of tungsten for projectiles.

Organization and employment

The sPzB 41 was used by some motorized divisions and by some Jäger, Gebirgsjäger and Fallschirmjäger units. Some guns were supplied to anti-tank and sapper units. The weapon was employed on the Eastern Front from the beginning of hostilities, until the end of the war and also saw combat in the North African Campaign and on the Western Front in 1944–45.

Variants

The sPzB 41 was also mounted on several vehicles, such as cars, half-tracks and armored cars:
Squeeze bore guns saw only limited use in World War II. Manufacturing such weapons was impossible without advanced technologies and high production standards. Besides Germany, the only country to bring such weapons to mass production was Britain, with the Littlejohn adaptor which, although not a gun in itself, used the same principle. An attempt by a Soviet design bureau headed by V. G. Grabin in 1940, failed because of technological problems. In the US, reports about the sPzB 41 inspired a series of experiments with 28/20 barrels and taper bore adaptors for the 37 mm Gun M3; the work started in September 1941 and continued throughout the war, with no practical success.
The sPzB 41 combined good anti-armor performance at short range and a high rate of fire with small, lightweight, dismantleable construction.
However, it also had several shortcomings, such as:
Some authors that criticize the sPzB 41 concentrate mainly on the short service life of its barrel. However, its chance of survival after 500 short-range shots was slim anyway. High-velocity guns with "normal" barrel construction also had a short service life, e.g. for the Soviet 57-mm ZiS-2 it was about 1,000 shots. In the end, the factor that brought production of the sPzB 41 to a halt was the shortage of tungsten.

Ammunition

There were two shell types for the sPzB 41: the armor-piercing 2.8 cm Pzgr.41 and the fragmentation 2.8 cm Sprg.41.
The Pzgr.41 had a tungsten carbide core, a softer steel casing and a magnesium alloy ballistic cap. The core was 40 mm long and 10.9 mm in diameter.